weileong's 4ft tank

[weileong]

You wanna nice one must always drop by there and see one. But buy too much you contribute to the cat brand car ah.... damn sai yang lei.

[Dispar_Anthias]

You wanna nice one must always drop by there and see one. But buy too much you contribute to the cat brand car ah.... damn sai yang lei.

Also not he drive one... jaguar is history.. dun worry wun come out another panther lah

[weileong]

No panther later come out the white hair ("B"uy "M"ore "W"orries) then how?

[flubberina13]

All so 'mo lei tao'...

It's the invasion of the Rojak Gang...

[Dispar_Anthias]

No panther later come out the white hair ("B"uy "M"ore "W"orries) then how?

BMW= break my wallet........ if got BRW= break reefers wallet

[weileong]

Washing my skimmer's collection cup after 1 week.

Warning disgusting shots, pls stay away if you can't take it

[weileong]

view from top.... yucks, no way am I gonna use my hands to pick up the skimmate nor use toilet paper to wipe it.

[weileong]

So I use the water and spray.... big thick BLACK (not brown) dry pieces are out.....

[flubberina13]

Ladies :

Reefers :

[weileong]

Foaming immediately after firing up

Because I shut down one beckett so the water level gets lower and after washing I fire up the other beckett so skimming in never interrupted. Warning very high bioload lol.

[weileong]

approx 50mins later

[blueheaven]

arrrggghhh!!!! I'm itching all over!!!! :lol:

[nutx]

Does your main chamber (or body) get dirty? do you clean it or just leave it?

[weileong]

Nope the main chamber does not get dirty so no need to clean. Depends on how you tune the skimmer.

If the main body gets dirty then you'll need to clean it as well. Not much issue just get a wet tissue and wipe it clean.

[nutx]

Nope the main chamber does not get dirty so no need to clean. Depends on how you tune the skimmer.

If the main body gets dirty then you'll need to clean it as well. Not much issue just get a wet tissue and wipe it clean.

my main chamber has very thick skimmate on the wall, abt 4inches. If I higher the water level, then the skimmate became very watery.

looks like I have to continue my routine of wiping the main chamber every week!

[weileong]

my main chamber has very thick skimmate on the wall, abt 4inches. If I higher the water level, then the skimmate became very watery.

looks like I have to continue my routine of wiping the main chamber every week!

Did you open the air valve too much?

Any big bubbles in the down tube? I think you open the air valve too much liao....

[AlfaRomeo]

Bro, which part is the down tube?

[weileong]

The smaller white tubes where your beckett injector is installed is called the down tube.

[Joe_P]

my main chamber has very thick skimmate on the wall, abt 4inches. If I higher the water level, then the skimmate became very watery.

looks like I have to continue my routine of wiping the main chamber every week!

to obtain dry skimate, try closing the air valve till you notice really fine bubbles...then adjust the water level to the base of the neck which leads to the collection cup... you should get really thick skimmate in no time....

[nutx]

Oh...ok, will try to re-tune the air-valve again. Previously, I on the air valve maximum...but the bubbles is still finer than my H&S.

[weileong]

Try to open the air valve at 50% then set the water level at the neck as recommended by Joe_P.

Beckett power right ??

[nutx]

Try to open the air valve at 50% then set the water level at the neck as recommended by Joe_P.

Beckett power right ??

when the air valve is fully open, the down chamber is pure white....when half open, bubbles looks finer, but like not alot of bubbles. the down chamber is not fully fill with bubbles.

Wonder could it be the difference due to the collection cup chamber height difference among the difference model.

[Joe_P]

when the air valve is fully open, the down chamber is pure white....when half open, bubbles looks finer, but like not alot of bubbles. the down chamber is not fully fill with bubbles.

Wonder could it be the difference due to the collection cup chamber height difference among the difference model.

What pump are you firing that Barr's unit of yours... If its a MD 55, you should be getting good results... even with the valve under throttle back half... a MD 40 might not get you the results you desire.... but would still work.

[DeepBlue]

i think he is using the mx70

[weileong]

i think he is using the mx70

I believe bro Nutx is using the resun MD55 to drive his Barr SK1600.

Even with my MX70 driving two beckett I had the two down tube completely white with fine bubbles. Somemore my down tubes are twice the length of yours.

I believe there is something stuck in your beckett injector, you should take it out for checking.