Jump to content

My 1.5 ft Reef log


jackywongto
 Share

Recommended Posts

Hey Hi Reefzz

yeah very clear :) like the Acrylic very much.

for your fan, I suggest you look in your storeroom to see if there is any unwanted power adaptor.

Can be laptop power, handphone charger et- any dc supply.

Most handphones are 5v dc. some pocket pc chargers are 12v

then you can go to any computer shops to get the fans.

The USB fans ones are 5v, others are 12v

The 12v large ones are about 10 - 14 SGD.

Becareful of the spinning blades though especially if you have kids.

There is no "fence" for the fans so you can get hurt by the exposed rotating blades.

I got cut by it last night. nasty.

You can the the fan guide from the shop you buy the fan.

I think is S$3 to S$4 EACH.

You need two pieces.Since your fan is expose both sides.

Don't take the risk bro

6.5 * 2 * 2 + 3.75 * 1.5 *1.5,(Decomn on 14/9/08)
4*2*2 + 2.5*1.25*1.25 (Decomn on 1/8/09)
5*2*2 (Fully LED light system, 140 3 watt SSC leds with 60 degree lens)(Decomm)
2.5*2*2(Fully LED Light System,96 3 watt SSC leds with 60 degree lens)(Decomm)

5*2.5*2(LED only)

Eheim return 1 * pump

1 HP Daikin compressor with cooling coil
2 Jebao OW40, 1 ecotech MP40,
1X6085 Tunze wm,

1 CURVE 7 Skimmer

  1 DIY 80 led control by Bluefish mini 

1 radion XR30W G2, 2 Radion XR15G3

Sump area lite by 5 ft T5 , 6 * SSC 3 watt red LED for refugium

1 Full spectrum E27 led light

1 CR control by bubble count

Start No Water Change since 1st Dec 2016

Add new 2.5x2x 1.5 ft 

 nLekOfpYts.jpg
[/quote]


 

Link to comment
Share on other sites

You can the the fan guide from the shop you buy the fan.

I think is S$3 to S$4 EACH.

You need two pieces.Since your fan is expose both sides.

Don't take the risk bro

Oh they sell the fan guide? hehe.. sure will get them.

looked at it again... quite scary... the blades rotating so fast....

Eqpt: Deltec MCE 600, Tunze 6055 with Tunze 7091 controller, Artica 1/15 HP chiller, AquaIllumination Sol Blue LED Light System

2011 resolution : Do it simpler, better and in an easier way!

Link to comment
Share on other sites

btw jacky, how would it be if need to install 2-3 fans, still follow the same rigging of one power adaptor ? :thanks:

wah testing me..... I return everything to my lecturer already like 20 years ago!

Trying to recall.... (YES I KNOW I AM MAKING A FOOL OUT OF MYSELF.... THANKS TO POOMOON)

as long as your ampere rating on the power adaptor is sufficent, you can connect in parallel.

My adaptor has a limit of 2.5A. My fan is only rated 0.37 A. So even if I have 4 fans connected in parallel, the total amps is only 1.48Amps

So the adaptor can still support. (I think the impedance has lowered though..... WTH... reliving all my nightmares.....)

I can be TOTALLY WRONG..... Better let Sherman verify that this is correct. He is in this line.

One more question like this and I will shoot you Poomoon ..... Lol kidding.....

Eqpt: Deltec MCE 600, Tunze 6055 with Tunze 7091 controller, Artica 1/15 HP chiller, AquaIllumination Sol Blue LED Light System

2011 resolution : Do it simpler, better and in an easier way!

Link to comment
Share on other sites

Wow, bullseye.

The balance can use to run 3 watt leds.

At least a dozen .

6.5 * 2 * 2 + 3.75 * 1.5 *1.5,(Decomn on 14/9/08)
4*2*2 + 2.5*1.25*1.25 (Decomn on 1/8/09)
5*2*2 (Fully LED light system, 140 3 watt SSC leds with 60 degree lens)(Decomm)
2.5*2*2(Fully LED Light System,96 3 watt SSC leds with 60 degree lens)(Decomm)

5*2.5*2(LED only)

Eheim return 1 * pump

1 HP Daikin compressor with cooling coil
2 Jebao OW40, 1 ecotech MP40,
1X6085 Tunze wm,

1 CURVE 7 Skimmer

  1 DIY 80 led control by Bluefish mini 

1 radion XR30W G2, 2 Radion XR15G3

Sump area lite by 5 ft T5 , 6 * SSC 3 watt red LED for refugium

1 Full spectrum E27 led light

1 CR control by bubble count

Start No Water Change since 1st Dec 2016

Add new 2.5x2x 1.5 ft 

 nLekOfpYts.jpg
[/quote]


 

Link to comment
Share on other sites

Its day 3 and the maroon clown has stopped attacking the false perc now :) yay!

There is some minor bickering but hopefully that will go off with time too.

^_^

Eqpt: Deltec MCE 600, Tunze 6055 with Tunze 7091 controller, Artica 1/15 HP chiller, AquaIllumination Sol Blue LED Light System

2011 resolution : Do it simpler, better and in an easier way!

Link to comment
Share on other sites

  • SRC Member
Its day 3 and the maroon clown has stopped attacking the false perc now :) yay!

There is some minor bickering but hopefully that will go off with time too.

^_^

It won't go away... :P The maroon clown will establish its territory and if your percs go near there, they will be chased back. Also, if your maroon clown and percs are about the same size, then the maroon clown won't be that aggressive.

My Setup:

3x2x2 tank with IOS

Equipment List:

Chiller: Artica 1/5HP

Chiller Pump: Sicce 4000

Return Pump: OR3500

Skimmer: Deltec APF600

Wavemaker: Tunze Wavebox/2x Hydor K2/SCWD wavemaker

Lights: DElighting 2x150W MH + 2x 39W T5 Atinic

FR: Skimz

FR Pump: Atman AT-104

Tubby ATO, Kalkweisser Reactor with magnetic stirrer.

Link to comment
Share on other sites

It won't go away... :P The maroon clown will establish its territory and if your percs go near there, they will be chased back. Also, if your maroon clown and percs are about the same size, then the maroon clown won't be that aggressive.

At least the maroon is not chasing the false clown round the tank now.

Saw them swimming together at close proximity which is good.

The false clown is slightly smaller.

Eqpt: Deltec MCE 600, Tunze 6055 with Tunze 7091 controller, Artica 1/15 HP chiller, AquaIllumination Sol Blue LED Light System

2011 resolution : Do it simpler, better and in an easier way!

Link to comment
Share on other sites

  • SRC Member
wah testing me..... I return everything to my lecturer already like 20 years ago!

Trying to recall.... (YES I KNOW I AM MAKING A FOOL OUT OF MYSELF.... THANKS TO POOMOON)

as long as your ampere rating on the power adaptor is sufficent, you can connect in parallel.

My adaptor has a limit of 2.5A. My fan is only rated 0.37 A. So even if I have 4 fans connected in parallel, the total amps is only 1.48Amps

So the adaptor can still support. (I think the impedance has lowered though..... WTH... reliving all my nightmares.....)

I can be TOTALLY WRONG..... Better let Sherman verify that this is correct. He is in this line.

One more question like this and I will shoot you Poomoon ..... Lol kidding.....

lol...

A man with a reef tank is a man with an empty wallet...

Link to comment
Share on other sites

  • SRC Member
At least the maroon is not chasing the false clown round the tank now.

Saw them swimming together at close proximity which is good.

The false clown is slightly smaller.

heh feeding time won't be that peaceful. Your maroon will boss the false perc, and over time will find that maroon will grow much bigger. Hope it works out though!

Link to comment
Share on other sites

heh feeding time won't be that peaceful. Your maroon will boss the false perc, and over time will find that maroon will grow much bigger. Hope it works out though!

hmmmm so far ok leh. ** keeping fingers very crossed.

anyway will try to post some vids tml.

My PH still quite low. 8.09

At night, it drops to 8.05

Will check tonight if the dKH has risen.

I have been dosing 5 ml of alkaline buffer for the past 3 nights already.

Eqpt: Deltec MCE 600, Tunze 6055 with Tunze 7091 controller, Artica 1/15 HP chiller, AquaIllumination Sol Blue LED Light System

2011 resolution : Do it simpler, better and in an easier way!

Link to comment
Share on other sites

  • SRC Member
hmmmm so far ok leh. ** keeping fingers very crossed.

anyway will try to post some vids tml.

My PH still quite low. 8.09

At night, it drops to 8.05

Will check tonight if the dKH has risen.

I have been dosing 5 ml of alkaline buffer for the past 3 nights already.

the ph range is fine bro, mine ranges from 8.10-8.2. The best indicator is your fishes and corals. If they are doing fine, then I wouldn't worry about getting them to 'optimal 8.2'.

Try to get more vigorous surface agitation. When I first started, my ph levels were hovering around 7.95-8.10. Think it may be because we use the same design: no sump, less turnover rate. After shifting my Vortech higher and aiming my return to create more agitation, it finally stabilized at my current range. :) My skimmer is my main aeration device, so whenever I turn off my skimmer for 12 hours when dosing my bacteria, I always run reef buffer to maintain ph, otherwise ph can drop to 7.8

Link to comment
Share on other sites

  • SRC Member
wah testing me..... I return everything to my lecturer already like 20 years ago!

Trying to recall.... (YES I KNOW I AM MAKING A FOOL OUT OF MYSELF.... THANKS TO POOMOON)

as long as your ampere rating on the power adaptor is sufficent, you can connect in parallel.

My adaptor has a limit of 2.5A. My fan is only rated 0.37 A. So even if I have 4 fans connected in parallel, the total amps is only 1.48Amps

So the adaptor can still support. (I think the impedance has lowered though..... WTH... reliving all my nightmares.....)

I can be TOTALLY WRONG..... Better let Sherman verify that this is correct. He is in this line.

One more question like this and I will shoot you Poomoon ..... Lol kidding.....

haha ... sorry and thanks :eyebrow: really a newbie who's trying to get into the hobby, and not even in engineering background, so bear with me :whistle:thanks: you can shoot me anytime, shoot me up with some free LPS / SPS haha

25 Gal Micro Ocean

Link to comment
Share on other sites

haha ... sorry and thanks :eyebrow: really a newbie who's trying to get into the hobby, and not even in engineering background, so bear with me :whistle:thanks: you can shoot me anytime, shoot me up with some free LPS / SPS haha

lol no worries....

have questions just shoot.... me reef newbie too....

Eqpt: Deltec MCE 600, Tunze 6055 with Tunze 7091 controller, Artica 1/15 HP chiller, AquaIllumination Sol Blue LED Light System

2011 resolution : Do it simpler, better and in an easier way!

Link to comment
Share on other sites

  • SRC Member
thanks ... nooby, but your tank really nice :yeah:

He's a "newbie" with very good equiptments! =]

cant wait to see you stock up your tank bro Jacky!

especially when u have ur girl to pressure you to get certain kinda corals/fishes/inverts which are not exactly what you wanted.. =P

A man with a reef tank is a man with an empty wallet...

Link to comment
Share on other sites

thanks ... nooby, but your tank really nice :yeah:

:thanks: very good encouragement to me :)

Eqpt: Deltec MCE 600, Tunze 6055 with Tunze 7091 controller, Artica 1/15 HP chiller, AquaIllumination Sol Blue LED Light System

2011 resolution : Do it simpler, better and in an easier way!

Link to comment
Share on other sites

  • SRC Member
:thanks: very good encouragement to me :)

You are a reef nooby...then I am not even a reef baby... :whistle

My Setup:

3x2x2 tank with IOS

Equipment List:

Chiller: Artica 1/5HP

Chiller Pump: Sicce 4000

Return Pump: OR3500

Skimmer: Deltec APF600

Wavemaker: Tunze Wavebox/2x Hydor K2/SCWD wavemaker

Lights: DElighting 2x150W MH + 2x 39W T5 Atinic

FR: Skimz

FR Pump: Atman AT-104

Tubby ATO, Kalkweisser Reactor with magnetic stirrer.

Link to comment
Share on other sites

  • SRC Member
then i would be a reef ... umm ... spore :P or just about to ...

Spore...as in SINGAPORE??? :eyebrow:

My Setup:

3x2x2 tank with IOS

Equipment List:

Chiller: Artica 1/5HP

Chiller Pump: Sicce 4000

Return Pump: OR3500

Skimmer: Deltec APF600

Wavemaker: Tunze Wavebox/2x Hydor K2/SCWD wavemaker

Lights: DElighting 2x150W MH + 2x 39W T5 Atinic

FR: Skimz

FR Pump: Atman AT-104

Tubby ATO, Kalkweisser Reactor with magnetic stirrer.

Link to comment
Share on other sites

installed the pinpoints.

Calibration for the PH monitors was madness.....

tedious and time consuming.

sorry for the blurry photo. Lazy to retake.:P

Eqpt: Deltec MCE 600, Tunze 6055 with Tunze 7091 controller, Artica 1/15 HP chiller, AquaIllumination Sol Blue LED Light System

2011 resolution : Do it simpler, better and in an easier way!

Link to comment
Share on other sites

reading as of 15 mins ago.

I need to velco these monitors to my cabinet.

PH was 7.9 a couple of days back. manage to raise it to 8.1

Will continue to try to hit 8.2

Eqpt: Deltec MCE 600, Tunze 6055 with Tunze 7091 controller, Artica 1/15 HP chiller, AquaIllumination Sol Blue LED Light System

2011 resolution : Do it simpler, better and in an easier way!

Link to comment
Share on other sites

installed a deflector on the return from my chiller.

This will cause more surface agitation... ==> more oxygen ==> higher PH

Eqpt: Deltec MCE 600, Tunze 6055 with Tunze 7091 controller, Artica 1/15 HP chiller, AquaIllumination Sol Blue LED Light System

2011 resolution : Do it simpler, better and in an easier way!

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share




×
×
  • Create New...