Jump to content

Is there such thing as too much flow??


Recommended Posts

  • SRC Member

Well.. seeking advice for this question Whether thr will be too much flow for a Mixed reef?? Currently running one a Hydor K2 tank volume is 34 gallons...... Thinking about this and i would appreciate any advice...

:thanks: in advance

Getting a new toy if it doesn't harm anything... :eyebrow:

1ft cube with IOS [the low tech tank]

1. JBJ C-breeze to keep temp hovering around 27-28'C

2. LED clip on - 120 bulbs

-skimmer-less-

My 3 humble equipments that keeps my tank running... [DRIED OUT]

1. The RSM itself of course 2.My NEW Deltec MCE-300 Skimmer 3. My trusty Arctica Chiller

Tank parameters:

Temperature maintained at 25.3'C to 24.7'C

No3: 10ppm(b4 the use of the deltec skimmer)

No3: 5ppm (after use of the skimmer)

Others? too lazy to measure...LOL

Camera- EOS 50D

Link to comment
Share on other sites

  • SRC Member

Short answer: Yes.

Mushies and other soft corals will be very unhappy with too much flow, may detach or close up and die... I think I killed some yumas when I went overboard with my 2100l/h return pump together with the K1 in my nano tank. Lesson learnt the hard way haha.

My 1.5ft nano cube

My 24G nano tank (Decommed)

I can picture in my mind a world without war, a world without hate.

And I can picture us attacking that world, because they'd never expect it.

-- Jack Handey

Link to comment
Share on other sites

  • SRC Member
Short answer: Yes.

Mushies and other soft corals will be very unhappy with too much flow, may detach or close up and die... I think I killed some yumas when I went overboard with my 2100l/h return pump together with the K1 in my nano tank. Lesson learnt the hard way haha.

However if i'm to just point the new toy ??? to the sps corner will it still do any harm?? :erm:

1ft cube with IOS [the low tech tank]

1. JBJ C-breeze to keep temp hovering around 27-28'C

2. LED clip on - 120 bulbs

-skimmer-less-

My 3 humble equipments that keeps my tank running... [DRIED OUT]

1. The RSM itself of course 2.My NEW Deltec MCE-300 Skimmer 3. My trusty Arctica Chiller

Tank parameters:

Temperature maintained at 25.3'C to 24.7'C

No3: 10ppm(b4 the use of the deltec skimmer)

No3: 5ppm (after use of the skimmer)

Others? too lazy to measure...LOL

Camera- EOS 50D

Link to comment
Share on other sites

  • SRC Member

Yup, depends on your coral placement and where you point the wavemaker. I shield my mushrooms with live rock now, to block the flow.

My 1.5ft nano cube

My 24G nano tank (Decommed)

I can picture in my mind a world without war, a world without hate.

And I can picture us attacking that world, because they'd never expect it.

-- Jack Handey

Link to comment
Share on other sites

  • SRC Member
possible, depends on how you play with it..... some wavemakers are just too strong....

hmm... then how much is considered really too strong... I'm not talking about vortechs in this case... :eyebrow:

1ft cube with IOS [the low tech tank]

1. JBJ C-breeze to keep temp hovering around 27-28'C

2. LED clip on - 120 bulbs

-skimmer-less-

My 3 humble equipments that keeps my tank running... [DRIED OUT]

1. The RSM itself of course 2.My NEW Deltec MCE-300 Skimmer 3. My trusty Arctica Chiller

Tank parameters:

Temperature maintained at 25.3'C to 24.7'C

No3: 10ppm(b4 the use of the deltec skimmer)

No3: 5ppm (after use of the skimmer)

Others? too lazy to measure...LOL

Camera- EOS 50D

Link to comment
Share on other sites

  • SRC Member
Yup, depends on your coral placement and where you point the wavemaker. I shield my mushrooms with live rock now, to block the flow.

Considering creating a turbid water movement whr two flows come together and creating havoc waves... :eyeblur::eyebrow:

1ft cube with IOS [the low tech tank]

1. JBJ C-breeze to keep temp hovering around 27-28'C

2. LED clip on - 120 bulbs

-skimmer-less-

My 3 humble equipments that keeps my tank running... [DRIED OUT]

1. The RSM itself of course 2.My NEW Deltec MCE-300 Skimmer 3. My trusty Arctica Chiller

Tank parameters:

Temperature maintained at 25.3'C to 24.7'C

No3: 10ppm(b4 the use of the deltec skimmer)

No3: 5ppm (after use of the skimmer)

Others? too lazy to measure...LOL

Camera- EOS 50D

Link to comment
Share on other sites

  • SRC Member
Considering creating a turbid water movement whr two flows come together and creating havoc waves... :eyeblur::eyebrow:

get controllables, they pulse so u can set for the left right motion , even with 2x 6105 at full blast 13000lph , my lps and mushies are so happy swaying arn

Mix Reef Tank: 5ft x 2.5ft x 2ft mixed reef

Chiller: daikin 1hp compressor

Return: Red Dragon 6.5m3

Lighting: Aqua Lumen Ocean 4ft

Skimmer: Reef Octopus RO-RPS-5000-EXT w/ Bubble Blaster

CR: RM 824 /milwakee PH controller

Tunze TS24 with 7096

Tunze Osmolator

American Pinpoint PH monitor

American Pinpoint ORP Monitor with Resun Ozone

RM sulphur denitrator

RM FR 424

RM FR 624

TLF Phosban Reactor

My old tank thread

469748_10150741487628605_529506809_o_zps36d5c396.jpg

Link to comment
Share on other sites

  • SRC Member
get controllables, they pulse so u can set for the left right motion , even with 2x 6105 at full blast 13000lph , my lps and mushies are so happy swaying arn

U mean like the magnum??!! :whistle

1ft cube with IOS [the low tech tank]

1. JBJ C-breeze to keep temp hovering around 27-28'C

2. LED clip on - 120 bulbs

-skimmer-less-

My 3 humble equipments that keeps my tank running... [DRIED OUT]

1. The RSM itself of course 2.My NEW Deltec MCE-300 Skimmer 3. My trusty Arctica Chiller

Tank parameters:

Temperature maintained at 25.3'C to 24.7'C

No3: 10ppm(b4 the use of the deltec skimmer)

No3: 5ppm (after use of the skimmer)

Others? too lazy to measure...LOL

Camera- EOS 50D

Link to comment
Share on other sites

  • SRC Member
U mean like the magnum??!! :whistle

magnum? i more refering to maybe tunze 6055 and a 7096 for your case

Mix Reef Tank: 5ft x 2.5ft x 2ft mixed reef

Chiller: daikin 1hp compressor

Return: Red Dragon 6.5m3

Lighting: Aqua Lumen Ocean 4ft

Skimmer: Reef Octopus RO-RPS-5000-EXT w/ Bubble Blaster

CR: RM 824 /milwakee PH controller

Tunze TS24 with 7096

Tunze Osmolator

American Pinpoint PH monitor

American Pinpoint ORP Monitor with Resun Ozone

RM sulphur denitrator

RM FR 424

RM FR 624

TLF Phosban Reactor

My old tank thread

469748_10150741487628605_529506809_o_zps36d5c396.jpg

Link to comment
Share on other sites

  • SRC Member
magnum? i more refering to maybe tunze 6055 and a 7096 for your case

That's too much flow liao... Bearing in mind that i'm still keeping my K2... Probably gonna get a K @@@@ agn :ph34r: ... My prev one was sold to a friendly reefer... Oh man my desk is very messy, thanks to the HBL... <_<

1ft cube with IOS [the low tech tank]

1. JBJ C-breeze to keep temp hovering around 27-28'C

2. LED clip on - 120 bulbs

-skimmer-less-

My 3 humble equipments that keeps my tank running... [DRIED OUT]

1. The RSM itself of course 2.My NEW Deltec MCE-300 Skimmer 3. My trusty Arctica Chiller

Tank parameters:

Temperature maintained at 25.3'C to 24.7'C

No3: 10ppm(b4 the use of the deltec skimmer)

No3: 5ppm (after use of the skimmer)

Others? too lazy to measure...LOL

Camera- EOS 50D

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share



×
×
  • Create New...