Jump to content

Resun MD40


terryansimon
 Share

Recommended Posts

I'm interested in getting one for my tank and I've got a few questions to ask.

can I use this pump to power my Teco RA680, Coralife Turbotwist 6x and Reef Maniac's Fluidized Reactor and my AquaC EV180? I'm intending to tee-off from the main output to the various equipments... this is how I intend to go about it

==> one pipe/hose tee-off to RA680. this pipe/hose will have a ball valve to control flow so that it will not exceed a certain rate for my RA680

==> one pipe/hose tee-off to Coralife Turbotwist 6x, whose output will be the input for Reef Maniac's Fluidized Reactor. will also have a ball valve to throttle the flow

==> one pipe/hose tee-off to AquaC EV180 skimmer. will also have a ball valve to throttle the flow.

is the above mentioned process possible? or is it too grandeur? :P also, will the pipe/hose sizing be similar? otherwise must spend $$$ to replace them again. sian 1/2

awaiting your friendly opinions/comments. (=

by the way this pump will replace three pumps...so really hope that it will work. but need some guru to some advice first. :P

Link to comment
Share on other sites

you know what? damn. :P

how about I power my chiller and Coralife Turbotwist and Reef Maniac's Fluidized Reactor with it? seeing how I only need to tee-off to two components.

eh wait.

4500l/h? I think enough what...EV180 = 2000l/hr. Turbotwist = 800l/hr. chiller = 800l/hr. hmm.

how come not enough? care to enlighten me? (=

Link to comment
Share on other sites

get the MD55 lah. more power.

n then u got to ensure that you are able to control how much flow goes where. quite difficult IMO. tee off maybe 33% each device.

using the valve also not veri accurate IMO.

I used to run 60-70% off my MD55 to run my return + two weipro skimmer. Really power. Not sure the rate for MD40.

Link to comment
Share on other sites

4500l/h? I think enough what...EV180 = 2000l/hr. Turbotwist = 800l/hr. chiller = 800l/hr. hmm.

There is two parts of the pump.

1. Flowrate

2. pressure

It's like current and voltage in electricity.

After the Resun MD40 has to push thru all the piping, Tee etc the pressure also lost already. Remember it is not pressure rated so the lost is more then it might not have enuff pressure to drive your EV-180 spray injector.

Give you an example, I tried to Tee off from MD55 to drive my EV-240 and the other used for main tank return, already not enuff flow.

Anway you can give it a try. Have you bought the MD40? I tried to use the MD40 to drive my chiller only thru abt 3m of tubing and the flow is already pretty weak.

Link to comment
Share on other sites

  • SRC Member

In my opinion, I think the chiller, the UV, the fluidized reactor do not required pressurated pump. So by tee-off from a pressurated pump, you lose the power that can be better utilized to drive your skimmer. Also, tuning it can be a hazzle and any adjustment made on the chiller, UV and fluidize reactor is going to affect your skimmer performance.

I would suggest to buy a cheap pump of 1000L/hr and drive the other 3. From a piping point of view is also a lot neater.

Link to comment
Share on other sites

I was actually thinking of decomissioning my Eheim 1262 meant for close loop and using it to drive the skimmer and tee-off to the Coralife Turbotwist.

and using my existing 1048 to power my Teco. hmm.

weileong...even if you lend me hor, I may not have the pipes/hoses lying around. hur. must go source first. *mutters*

Link to comment
Share on other sites

If your mind already made on either the MD40 or MD55 (both takes the same hose size) then you'll have to do the piping so get it done then plug the pump in after that you can go buy the right pump.

Partick: The MD40 is not pressure rated. The MD55 is way way way too powerful for the EV-180 so you have to Tee off and hence do not waste the power! Not too many skimmer can take the MD55, even the EV-240 needs to tune down the flow.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share



  • Join us on the largest Reefing community in Asia!

    Sign up and share your reefing journey with us, make friends and get helps from the community .

     

  • Topics

  • Latest Update

    1. 0

      格里菲斯大学申请学校Griffith毕业证成绩单信封Q/微993398773办理澳洲大学毕业证文凭留信认证留服认证教育部认证回国证明澳洲本科文凭硕士学位证毕业证Griffith University

    2. 0

      康涅狄格大学毕业证丢失UCONN毕业证成绩单Q/微993398773办理美国大学毕业证学位证留信认证留服认证教育部认证回国证明美国本科学位证硕士文凭成绩单 University of Connecticut

    3. 0

      西蒙菲莎大学未正常毕业SFU毕业证书Q/微993398773办理加拿大大学毕业证成绩单留信认证留服认证教育部认证回国证明加拿大本科文凭硕士学位证毕业证Simon Fraser University

    4. 0

      悉尼科技大学申请学校UTS毕业证成绩单信封Q/微993398773办理澳洲大学毕业证文凭留信认证留服认证教育部认证回国证明澳洲本科文凭硕士学位证毕业证University of Technology Sydney

    5. 0

      旧金山大学毕业证丢失USF毕业证成绩单Q/微993398773办理美国大学毕业证学位证留信认证留服认证教育部认证回国证明美国本科学位证硕士文凭成绩单University of San Francisco

×
×
  • Create New...