Jump to content

Reef Wonder Mini


Recommended Posts

  • SRC Member
Just need to be on stand by to qt and also a cover for the tank... My AT jump out... First time hear lorh... So sad

Sent from my HMA-L29 using Tapatalk



that’s rough.. sorry for your loss. heart pain sia.. AT somemore. them being the same genus probably made it worse


Sent from Singapore Reef Club mobile app
Link to comment
Share on other sites

  • SRC Member

was wondering why the ph of the cr does not drop even when the carbon doser is running... thanks to the apex who monitor and control my cr ph level...

thus i run a line trace...and found the leakage point at the connection of the check valve.... 

redid my co2 line and all is fixed and well now...

 

with my alkatronic monitoring my dkh.... i can control the duration and how the dkh jumps...

 

so looking forward to getting a stable dkh tune in with alkatronic and apex running hand in hand...

Link to comment
Share on other sites

  • SRC Member

Using the 3d printer to print the supporting bracket to hold up the light arm as I have added additional stuff to a light arm which is meant for just one light fixture...

Added it so that the arm will not have too much strain on the clamp for the light arm on the glass.. and also allow a more stable fixture...

The wonders of an 3d printer... Is you can customise anything which u can design out...7aca8987028ac9f4bc9d081a9c851c85.jpgb143a3ed380983bfe3ed0d3510022f04.jpg

Sent from my HMA-L29 using Tapatalk

Link to comment
Share on other sites

  • SRC Member

This is a prototype, thus only one was printed to test out the sizing and concept... So I will print and add more to hold it steady


Try it out and the light is already giving the tank a brighter overall feel... Thanks to RMS for the illumagic Vitamini.. the size and form factor is gooda715bd41b1740db26be4195f31a6bec2.jpg5c216b593ba188bd4ee8d3d614441024.jpg

Sent from my HMA-L29 using Tapatalk

Link to comment
Share on other sites

  • SRC Member

Over the last few days I have noticed that my alkatronic was stable at 7plus then all of the sudden a drop... To 4dkh..

Did a run, and observed that the pump A tube is leaking air thus the volume taken in via the Perks tubing is below the usual volume of 50ml

The tubing is original from the factory thus it is overdue for replacement...

Change out the tubing and realised that the dkh of 9.1 is where my tank dkh is at... So I knw that my original setup dkh of my tank was the correct one..


so I think routine checks on equipment is important..

Sent from my HMA-L29 using Tapatalk

Link to comment
Share on other sites

  • SRC Supporter
1 hour ago, Daniel Poh Yang Zheng said:

Added another light bar to my tank

Diy a holder for the light barc92f6624ed74613ef3021bfeb3863b83.jpg

Sent from my HMA-L29 using Tapatalk
 

Looks good. How is the material holding up to the heat?

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Member

1467897824_Screenshot2020-05-08at9_23_31PM.thumb.png.77f21dc8e828ffaccb220943e8d70cfc.png

Loving this system....able to ensure i can keep track of my system without having physically around...

Will be installing Water Leak Detector in the days to come to help to ensure no major water leakage due to equipment failure...

will look for float value to link it into breakout box...

 

Link to comment
Share on other sites

  • SRC Supporter

This is a very good idea !

DIY add-on to my Overflow area...


Manage to print a Durso covercap to ensure a quiet overflow without the gurgling

So Far, my overflow is quiet... default_smile.png 8b118fe2eb367bcc536bf0fdcc913886.jpga3a55f2b6de180fbbc74c6c26f10f5b4.jpge83e3b0d4ff7e4bfd199be9b8fdcf957.jpg

Sent from my HMA-L29 using Tapatalk




Sent from Singapore Reef Club mobile app

Link to comment
Share on other sites

  • SRC Member

Ran into some issue with my alkatronic...

Manage to reflash the firmware software...and I manage to solve all the issue...

So a brand-new recalibration for pump a and c...

And let's see how things goes...

Sent from my HMA-L29 using Tapatalk

Link to comment
Share on other sites

  • SRC Member
Nice 3D printing there. I'm wondering, why not just mount the light onto the shelf instead? Couple L brackets can do the job.
I don't really wanna destroy the shelving... And the shelve isn't solid wood, so may run into delamination in future... So yup... Less risky :)

Sent from my HMA-L29 using Tapatalk

Link to comment
Share on other sites

  • SRC Member

Did a recalibration of alkatronic and ph probe too as the dkh values keep on moving around...

So change out the tubing once again and did a full calibration...

Right now trying to see what I can do...

No3 is at 10ppm
Po4 is at 11ppb which is like 0.034

Abit out of sync...


SPS start to show Abit of stress...

Trying to stablise my tank :)

Sent from my HMA-L29 using Tapatalk

  • Like 1
Link to comment
Share on other sites

  • SRC Member

3/4 of my SPS is having the effect of the water property swing...
Burn Tips to StN to algae at the tip...

So there isn't much we can do now but to wait for the values to stabilize and also lower the intensity of the light...


Po4: 13ppb - 0.04ppm
No3: 5 to 6ppm

Dosing Bacteria and Amino Acid in hope for recovery of sps

Sent from my HMA-L29 using Tapatalk

Link to comment
Share on other sites

  • SRC Member

was talking to some experienced reefer... and decided that i should do a recovery test for my tank...

lately my tank has experienced both a alk spike and also high light par due to extra changes to the tank and also not knowing the full parameters of the tank...and maybe at the same time with some bleaching ongoing...added some form of stress to the tank...

so i am dosing heavily on Bacteria and also Coral food in hope that the tank will slowly recover....

 

 

Link to comment
Share on other sites

  • SRC Member
Burn tip can cause due to Low nutrients and high Kh and dosing bacteria will further cause burn tips and stn of ur Kh is too high.
What is ur Kh


Sent from my iPhone using Tapatalk
I am dosing amino to up my nutrient... Kh is abt 7.9 to 8.2

Sent from my HMA-L29 using Tapatalk

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share




  • Join us on the largest Reefing community in Asia!

    Sign up and share your reefing journey with us, make friends and get helps from the community .

     

  • Topics

  • Latest Update

    1. 0

      专业制作美国普渡大学西拉法叶校区大学毕业证》Q/微信751558146丨办理普渡大学西拉法叶校区毕业证成绩单,文凭留信网认证,保录取Purdue University,West Lafayette

    2. 0

      〖国外毕业证书〗加拿大MSVU圣文森山大学毕业证成绩单〖Q/微信751558146〗办理文凭教育部学历学位认证Mount Saint Vincent University

    3. 0

      专业制作美国福特汉姆大学毕业证》Q/微信751558146丨办理福特汉姆大学毕业证成绩单,文凭留信网认证,保录取Fordham University

    4. 0

      〖国外毕业证书〗加拿大McGill麦吉尔大学毕业证成绩单〖Q/微信751558146〗办理文凭教育部学历学位认证McGill University

    5. 0

      专业制作美国PITT毕业证》Q/微信751558146丨办理匹兹堡大学毕业证成绩单,文凭留信网认证,保录取University of Pittsburgh

×
×
  • Create New...