Jump to content

Where to get suitable bioball to mod impeller?


ervine
 Share

Recommended Posts

  • SRC Member
how did u do the bottom of the intake? the part there the air tude is slot in

See here... http://www.sgreefclub.com/forum/index.php?showtopic=14736

Basically it's a normal PVC tubing heated and twisted with a pliers until it starts to bottleneck... then simply drill a small hole just enough for the little air tubing elbow to go in and super glue it in place..

As for the connection to the pump, heat the tubing again and squeeze it till it moulds over the intake of the pump... completely no damage or modification to the pump for this part...

The elbow is there coz it's part of my skimmer... so that part can ignore...

Link to comment
Share on other sites

  • SRC Member
then i dont think my pump can do it unless i supply it with a control valve and an air pump cos my PH air inlet is a default one.. somehow pushing water out of it.. crazy manz!

You have to modify your pump to make it work with the needlewheel impeller, the air inlet for most (if not all) pumps comes at the outlet..

See the pics above... the venturi intake is not at the output but rather at the input...

Link to comment
Share on other sites

  • SRC Member
sorry guys, i am rather ignorance to this. care to explain the need for the "twisted" point?

thks!

It's not so much the twisting, it's the constriction that matters. It's just I achieved that constriction with a simple twist.

This constriction forces water to move at a higher velocity through the constriction, this higher velocity in turn sucks in air from the air intake.

Link to comment
Share on other sites

and also. Is the "blade" of the impeller is actually being replaced by the brush construction? If so, how do the water get sucks into the modified impeller and then being push back out to the main tank? All along I thought the blade works like a typical fan. When spinned, it draws air and then pushes it out through the other side cos of the slanted blade structure?

This is very intersting. Care to share more about this?

Link to comment
Share on other sites

  • SRC Member

Huh... only airstone driven skimmers need an air pump.. so yes, the movement of the water will naturally draw in the air...

As for blades, I don't know how to explain it but it still moves water.. although it's notably less than if it were the fans... centrifugal action? shucks cannot remeber the term..

But anyways, the curving of the blades you mentioned (like a typical table fan) works when the movement of fluid is straight past the blades, for the case of centrifugal (not sure if I'm right) the movement is in and then out at 90 degrees.... something like that lah...

Aiyah as long as it still moves water lah...

Link to comment
Share on other sites

  • SRC Member
and also. Is the "blade" of the impeller is actually being replaced by the brush construction? If so, how do the water get sucks into the modified impeller and then being push back out to the main tank? All along I thought the blade works like a typical fan. When spinned, it draws air and then pushes it out through the other side cos of the slanted blade structure?

This is very intersting. Care to share more about this?

Think of centrifugial force. The blades of the impellor does not work like a fan. It draws water into the centre of the impellor and forces it out the circumference to the outlet of the pump. :D

Comments are welcome!
Link to comment
Share on other sites

  • 4 weeks later...
  • 6 months later...
  • SRC Member

I took replaced the modded impeller with the original one already... so the modded one is lying around, anyone wants to buy it over from me?

Impeller only ah.. the maxijet is now used as a wavemaker (sawed off the output nozzle)

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share



  • Join us on the largest Reefing community in Asia!

    Sign up and share your reefing journey with us, make friends and get helps from the community .

     

  • Topics

  • Latest Update

    1. 0

      格里菲斯大学申请学校Griffith毕业证成绩单信封Q/微993398773办理澳洲大学毕业证文凭留信认证留服认证教育部认证回国证明澳洲本科文凭硕士学位证毕业证Griffith University

    2. 0

      康涅狄格大学毕业证丢失UCONN毕业证成绩单Q/微993398773办理美国大学毕业证学位证留信认证留服认证教育部认证回国证明美国本科学位证硕士文凭成绩单 University of Connecticut

    3. 0

      西蒙菲莎大学未正常毕业SFU毕业证书Q/微993398773办理加拿大大学毕业证成绩单留信认证留服认证教育部认证回国证明加拿大本科文凭硕士学位证毕业证Simon Fraser University

    4. 0

      悉尼科技大学申请学校UTS毕业证成绩单信封Q/微993398773办理澳洲大学毕业证文凭留信认证留服认证教育部认证回国证明澳洲本科文凭硕士学位证毕业证University of Technology Sydney

    5. 0

      旧金山大学毕业证丢失USF毕业证成绩单Q/微993398773办理美国大学毕业证学位证留信认证留服认证教育部认证回国证明美国本科学位证硕士文凭成绩单University of San Francisco

×
×
  • Create New...