Jump to content

Refractometers & Mixing Salt


SubzeroLT
 Share

Recommended Posts

  • SRC Supporter

A short write up on common issues reefers face when mixing salt water. This article aims to covers a couple of areas:

  1. Consistency issues with large buckets of salt mix (top vs bottom)
  2. How optical refractometers work. Selecting the right refractometer. Calibration method
  3. Other processes that may adversely affect the water parameters (eg. Prepare salt for specific gravity of ~ 1.025. But when you measure the Ca, Mg, KH parameters, it’s NOT as per published numbers)
  4. Hands on with branded vs ‘cheap’ refractometers. And cross check with a calibration fluid. This article focuses on the handheld optical refractometers.

 

Some are mine. Some are borrowed.

PC150280 (Small).jpg

 

PC150285 (Small).jpg

PC150292 (Small).jpg

 

Examples of why inaccurate salinity measurement is detrimental

  • Prolonged incorrect salinity parameters will negatively impact coral growth or reproduction rates
  • Ineffective hypo salinity treatment for breaking ich parasite cycle or quarantine. 
  • Incorrect target Ca, Mg, KH parameters. More effort needed to compensate with dosing methods
     

Mixing salt
Some salt brands mention to remix the bucket of salt but some don’t. The reality is that for any brand or type (evaporative or synthetic salts), smaller/heavier elements like magnesium will sink to the bottom of the bucket due to vibration during transportation. You end up with more calcium salt at the top & more magnesium salt at the bottom. 

This means that the water parameters of a new bucket of salt can be fairly ‘different’ from that from the bottom of the bucket. 

While some feel this difference does not matter, some others are very particular on chasing water parameter numbers but ignore step. One best practice for ensuring consistency is to remix the dry salt – Split the salt to different buckets then recombine back for storage. Just a 10 minute task.
 

IMG_0402[1] (Small).jpg

 

Mix it manually or roll the partially filled bucket to mix. Then recombine all the salt back into the original bucket for storage.

IMG_0410[1] (Small).jpg

 

Salinity & its relationship with specific gravity.

Salinity
The important unit of measure for seawater is “Salinity”. This is a measure of the weight of salts dissolved in 1000 weight of water (eg. 35g of salt in 1000g of water)  The salinity of most seawater ranges between 34PPT-36PPT (parts per thousand) depending on the location. Hence the widely accepted practice of targeting the average of 35PPT 


It is this total amount of salts that give you the final water parameters. Putting more salt (eg. 36ppt) will naturally give you higher Ca, Mg, KH numbers compared to 35ppt.

 

Specific Gravity (SG)
This is a relative density measurement. That is, a ratio of density of a given substance to the density of water. Specific gravity is a good alternative and practical method of measuring salinity.


Having said that, it is important to understand various aspects around specific gravity.


A common mistake is that most reefers shoot for is a specific gravity of 1.025. However, this number does not necessarily get you 35ppt salinity. Factors such as ambient temperature and refractometer calibration accuracy affect the target specific gravity.

 

Refractometer 

Many of us use hand held optical refractometers for practical purposes. It works on the fundamental physics principal of light refraction (bending light across a surface), and comparing the relative difference between the refraction of pure water vs salt water.

Liquids with higher salinity has a higher refractive index & will bend light more. This shows up as the location of ‘blue line’ on the specific gravity scale.
 

Some facts:

Most refractometers from LFS or ebay in the US$30 range are designed for “brine”.

  • Brine is a generic term for salt water which is composed of mostly sodium chloride. One common use of brine is for preserving food in salt water.
  • Note that Brine is NOT the same as sea water (Chloride, Sodium, Sulfate, Calcium, Magnesium, Potassium & other minor constituents). Hence the behavior under the refractometer is different.
  • If using a brine refractometer, be aware it has a salinity offset compared to sea water at various temperatures.

The generic refractometers have a salinity scale from 0-100ppt. For our purpose, we measure around the 35ppt region only. 

While some may get by with generic brine refractometers, many prefer paying slightly more for seawater specific ones for better accuracy. Key differences are build quality & materials used. 

  • For example, the DD refractometer body is made of copper – this ensures quicker water/tool temperature equalization and also more consistent ATC (auto temperature compensation)
  • Cheaper refractometers have a plastic or aluminum body which makes the temperature equalization slower & less accurate.

Table1 (Large).JPG

 

  • As mentioned earlier, specific gravity is a measure of density (i.e. mass / volume). As temperature increases, water volume increase as well. Hence for a particular salinity level (eg. 35ppt), specific gravity change at different temperatures. 
  • Temperature is one of the single most important factors influencing accurate refractometer readings and is one of the largest sources of error in measurement. Refractive index is VERY dependent on temperature.
  • The common refractors used in the hobby have ATC (Automatic Temperature Compensation). The ATC mechanism is simply a bi-metallic strip : an assembly of 2 different metals which expand/contract at different rates. Causing it to bend up or down to change the position of the visual scale to ‘compensate’ changes in refractive index of the water being measured.

 

Refrac2.jpg

 

  • For the Auto temperature compensation to work properly, you must allow the test sample & refractometer body temperature to equalize. Best practice is to place your sample then wait 10-20 seconds before taking a reading.

 

Refrac3.jpg

** Image from http://www.refractometer.pl/hand-held-refractometer

 


Calibrating refractometer. 

  • Calibration is to reset the 0 PPT / 1.0 SG point to ensure the refractometer is accurate for the operating temperature range specified (eg. 10deg to 40deg C). Essentially, what calibration does is to move the viewfinder scale up/down by tuning a small screw. 
  • Most refractometers have a label stating “20/20”. This means it’s designed & was originally factory calibrated at 20degC. The behavior of the bimetal strip ATC & optics is tuned to this set point.
  • To do this properly in our warm climate, you need to cool the refractometer body to 20degC (eg. in a 20degC air con room)
  • With the refractometer at 20DegC, place RODI water on the prism. Wait 20s. Then tune the screw till it reads 0 PPT / 1.0 SG 
  • A common mistake is to zero the refractometer at ambient condition that is not 20degC.  Here you see a slight offset in reading RODI water. If you had done so, the salinity of the salt you are getting would be ~ 1.5ppt lower than your target.

 

_IMG_1310 (Small).jpg

** Pardon the unsharp refractometer reading pictures as they were taken with an iphone

 

  • A common question is how the cheap refractometers compare with branded ones. As seen in the picture below, the unbranded brine refractometer reads approx. 1.5ppt higher than sea water specific ones.

_IMG_1437 (Small).jpg

 

  • I personally prefer the rubber cap over the calibration screw port. Threaded ones are troublesome to remove & prone to water getting in. The DD one has a thoughtful design that minimizes chances of losing the cap compared the Brine or Red Sea one

PC290098 (Small).JPG

 

PC160028 (Small).JPG

 

Target water parameters


Only a few salt manufacturers publish the recommended salinity/SG/temperature mixture. Here is an example :

DD Salt parameter (Small).jpg

https://www.theaquariumsolution.com/product/3035/124

 

Often, we use a water pump to help mix the salt in a drum/bucket of water. Care should be taken to prevent the mixture salts from precipitating. This means that an insoluble solid has emerged from the solution which can also alter the published water parameters. 

In most cases, mixing salt for 1-3 hours should be sufficient. Do not mix for excessively long periods. The heat from the water pump may cause calcium carbonate precipitate. Tell-tale sign is cloudy water if that happens.

Avoid leaving the pump turned on overnight in an open container. This can draw CO2 from the air into the water & change the chemistry of carbonate towards bi-carbonate. This also leads to some precipitation

 

Parting notes


I hope this short write up highlights some areas to watch out for when preparing salt mix – selecting a good refractometer & proper calibration to ensure the right salinity/specific gravity is reached. And some best practices to obtain consistent water parameters every time new salt is mixed.

Cheers :D

 

 


 

  • Like 3

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Supporter
42 minutes ago, Reef2Max said:

how often do you think we should calibrate our refractometer for accuracy ? 

Don't think there are any strict rules about this. Suggest check it monthly for accuracy (eg. with calibration fluid).

If it drifts beyond your comfort levels, then re-calibrate it. So far, I've ended up calibrating it about 1-2 times per year

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • 4 weeks later...
  • 2 months later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share



  • Join us on the largest Reefing community in Asia!

    Sign up and share your reefing journey with us, make friends and get helps from the community .

     

  • Topics

  • Latest Update

    1. 0

      加拿大保录取_SFU毕业证成绩单——Q微信751558146西蒙菲莎大学学位证_成绩单_办理SFU文凭学历认证Simon Fraser University

    2. 0

      美国学位证_Brandeis毕业证成绩单+Q微信751558146布兰迪斯大学学位证_成绩单_办理Brandeis文凭学历认证Brandeis University

    3. 0

      加拿大保录取_UBC毕业证成绩单——Q微信751558146英属哥伦比亚大学学位证_成绩单_办理UBC文凭学历认证University of British Columbia

    4. 0

      美国学位证_PSU毕业证成绩单+Q微信751558146宾州州立大学学位证_成绩单_办理PSU文凭学历认证Penn State University Park

×
×
  • Create New...