Is hailea 90A can support 5ft x 2ft x 2.5ft tank?

[jas coral]

Need advise on chiller, whether hailea 90A can support a 5ft by 2ft by 2.5ft tank with sump 3.5ft by 1.5ft by 40cm?

Edited December 24, 2017 by jas coral

[leong_rei]

Don't think can even can u need to waste alot electric bill as it may run non stop

Sent from Singapore Reef Club mobile app

[jas coral]

4 hours ago, leong_rei said:

Don't think can even can u need to waste alot electric bill as it may run non stop

Sent from Singapore Reef Club mobile app
 

Any recommendation of chiller?

[leong_rei]

Go for compressor

Sent from Singapore Reef Club mobile app

[leong_rei]

Or 1hp hailea

Sent from Singapore Reef Club mobile app

[jas coral]

3 hours ago, leong_rei said:

Or 1hp hailea

Sent from Singapore Reef Club mobile app
 

I was considering this 1hp hailea. But was recommended teco TK 1000.

[jas coral]

Anyone using teco TK 1000, need review?

 

[christan1959]

U need TK2000 

[jas coral]

On safe side, should be tk 2000

[leong_rei]

U need tk2000

Sent from Singapore Reef Club mobile app

[leong_rei]

If got the place get compressors save power save $$$$$ tk2000 is dam ex

Sent from Singapore Reef Club mobile app

[jas coral]

On 24/12/2017 at 11:09 PM, leong_rei said:

If got the place get compressors save power save $$$$$ tk2000 is dam ex

Sent from Singapore Reef Club mobile app
 

Dun hv space. Only can put inside cabinet..

[Angel Keeper]

I'm using that chiller for my tank the same size as yours for the past 4 years... Kicks in once every 4 hours and it runs for about 45 mins each time...

Sent from my SM-G935F using Tapatalk

[leong_rei]

U use 90a for 5 by 2 by 2.5 with sum tank ??? Only run 45min ???? Your house got on air con ???

Sent from Singapore Reef Club mobile app

[jas coral]

13 hours ago, Angel Keeper said:

I'm using that chiller for my tank the same size as yours for the past 4 years... Kicks in once every 4 hours and it runs for about 45 mins each time...

Sent from my SM-G935F using Tapatalk
 

U mean tk 2000?

[Angel Keeper]

U mean tk 2000?

I mean Hailea 90A...

Sent from my SM-G935F using Tapatalk

[jas coral]

1 minute ago, Angel Keeper said:

I mean Hailea 90A...

Sent from my SM-G935F using Tapatalk
 

90A can support 5ft by 2.5ft? Most people advised, go for bigger chilled but your kick in n runs time seem quite good.

[Angel Keeper]

90A can support 5ft by 2.5ft? Most people advised, go for bigger chilled but your kick in n runs time seem quite good.

I'm telling you from experience... Of course bigger size or compressor may be better... But what I'm trying to put across is that it is able to support the tank this size...

Sent from my SM-G935F using Tapatalk

[jas coral]

18 minutes ago, Angel Keeper said:

I'm telling you from experience... Of course bigger size or compressor may be better... But what I'm trying to put across is that it is able to support the tank this size...

Sent from my SM-G935F using Tapatalk
 

Thanks for your information.

[jas coral]

On 26/12/2017 at 1:18 PM, Angel Keeper said:

I'm telling you from experience... Of course bigger size or compressor may be better... But what I'm trying to put across is that it is able to support the tank this size...

Sent from my SM-G935F using Tapatalk
 

Do u use external probe for your chiller?

[Angel Keeper]

Do u use external probe for your chiller?

No I don't... But I got someone to modify the probe to be in my display tank for consistency...

My chiller input is tee off from my return pump and the output is returned to my sump... Thus the sump got chilled much faster and the chiller kept kicking in... After I placed the probe in the DT, the chiller kicked in at a lower frequency as the probe now measures the temperature of the whole water volume instead of only the sump...

Hope that helps...

Sent from my SM-G935F using Tapatalk

[jas coral]

4 minutes ago, Angel Keeper said:

No I don't... But I got someone to modify the probe to be in my display tank for consistency...

My chiller input is tee off from my return pump and the output is returned to my sump... Thus the sump got chilled much faster and the chiller kept kicking in... After I placed the probe in the DT, the chiller kicked in at a lower frequency as the probe now measures the temperature of the whole water volume instead of only the sump...

Hope that helps...

Sent from my SM-G935F using Tapatalk
 

Thank for your information