Jump to content

My Slice of Nature (Part 3)


SubzeroLT

Recommended Posts

  • SRC Supporter

Been super super busy with work the past 2 months. Missed a couple of water changes. But I made it a point to dose trace elements + a quick check on the Alkatronic / Mastertronic just to make sure things don't go haywire.

One knows the tank husbandary has failed miserably when you find aiptasia growing on the front top edge of the tank! These are easy to remove - just peel off with a blade.

92637475_20211214_103817221_iOS_edited(Medium).jpg.26055a00101ab6c62a717e6e581d8845.jpg

 

And phosphates creeping up to 0.184ppm

20211213_132808171_iOS_edited.jpg.4ca401cb018acb65e40de1e209895d75.jpg

 

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Supporter

Finally did some clean up. Over the weekend & past few nights.

Prime Fuge  has done a fantastic job with the refugium. Instead of the regular cheato, i'm growing hair algae on a mesh screen inside the refugium box. Something like an ATS, but with more water volume for the pods to reproduce. 

1897491888_20211215_002429064_iOS(Medium).jpg.146393c35b938fd87a0f08bdf17d6fa4.jpg

 

What it looks like in white light

1794990762_20211215_002504521_iOS(Medium).jpg.3596d02178165b5487f5c3e1ee6537fd.jpg

 

140653890_20211215_030421494_iOS(Medium).jpg.508e7e6808a4b4462135145e0a061e07.jpg

 

Gave the bio media a quick rinse with wank water. Have about 8 bags of bio media in that section.  A mix of bacteria king media, Maxpect biospere & Siporax. That shell on top of the bio media is the resident Halloween Crab living in the sump.

228866706_20211215_031813169_iOS(Medium).jpg.de321efd8f86f640dcd207cb3714e64a.jpg

 

Last cleaned about 3 years ago. Surprisingly they weren't dirty at all. 

1700801237_20211215_051045385_iOS(Medium).jpg.1e247c8129d6a443b385a8f81bf6a542.jpg

930015914_20211215_051117752_iOS(Medium).jpg.7be13afdea1b71d44b656816557a57b3.jpg

 

 

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Supporter

I'm currently running rowaphos in a typical tall reactor but found 2 issues with it :

1) After a while the rowaphos tends to stop churning/fluidizing. And water that goes in the reactor starts to 'channel'. That is, water flows through small paths of least resistance and do not have effective contact with all the media in the reactor

2) Not so much an issue but an inconvenience to have to disconnect the tubes to the reactor then lift the full reactor out of the sump. My sump is quite packed & need to carefully navigate the reactor through tubes & wires.

 

The sump clean up effort was also to make space for the Nyos Torq G2 to solve the above issues.

Below is the new Torq G2 1.0 body (right side). Compare that with the old Gen1 - 2.0 sized body (on the left). 

The 1.0 sized body is smaller but good enough for me - only running rowaphos.

The 2.0 body has plenty of volume. Its actually a good size for running bio pellets.

666080274_P1010184(Medium).JPG.a84479155982c2c6bda70f992eb0233e.JPG

 

Now has a fine mesh. Seems to do a good job keeping small media like rowaphos above the mesh.

70666490_P1010191(Medium).JPG.51629e42b2e3c3a6dc3f24659c18d01f.JPG

 

Also comes with a larger mesh. Good for less restricted flow or for larger media.

1520322934_P1010192(Medium).JPG.fd3aec238d80125def551e63d5e6db98.JPG

 

The top sponge has a slit at the top. This is an exit path for water to prevent internal pressure from building up in case the sponge gets clogged. 

1581031284_P1010194(Medium).JPG.3a4c75887158bfeb31c4b4fdea81a8bf.JPG

 

One thing I found was that its now very convenient to rinse the rowaphos. Its really as simple as just pouring clean water from the top & let the dirty water flow through the bottom mesh. After a few liters, its all clean.

Effortless!

1320469698_P1010199(Medium).JPG.127da1c61e095894c77d62bfbf87fd59.JPG

 

Both the top & bottom have a locking mechanism. This finally solves the big issue of the older generation where the lids can slip off.

761625785_P1010200(Medium).JPG.165cf6ef76ed7f99dceb174ef7ba962b.JPG

 

I put this amount for my 850L tank. That's about 1/3 bottle of Rowaphos.

1327506167_P1010202(Medium).JPG.b401f4c1418915f102fcaf4f7d7c6aac.JPG

 

Woot! Fluidizing very nicely in the chamber. And easy to adjust the flow. Clockwise to reduce the flow. Anti clockwise to increase flow....just like running a tap.

1276767940_20211216_031822124_iOS(Medium).jpg.60f9aadf6d02ef1dd11e59bf1ed6a4a9.jpg

 

  • Like 2

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Supporter

Exciting news that AI Hydra lights will soon be Mobius platform (similar to the rest of Ecotech). I got roped in to help with beta testing. Very nice interface and includes templates & additional features compared to the native AI app.

Will share more at a later time. Here is a screen shot :

946393993_20211216_092934000_iOS(Medium).png.e598d6338e1470d9fbf0ca825ecba16c.png

 

 

 

 

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Supporter

Partial tank shot 31058968_20211216_093751506_iOS_edited(Medium).jpg.f8dbcf88d64ea250303218505e688f19.jpg

 

If you recall, I made an overflow style secondary chamber filled with calcium reactor media. This was one way to receive low pH water from 2 sources (calcium reactor + sulfur reactor) with a single chamber (to save space). Made some modifications to raise the height of the funnel to gain more water pressure margin.

468674999_P1010207(Medium).JPG.82ff6c2d63f3ba1dfabc4cdfb8e884e2.JPG

 

Also raised the height of the drain adapter.

image.png.920faf9cf15e72b85f727ee504601200.png

 

image.png.f9754ea4dff1fe0f16f32cedd37fe6a8.png

 

 

  • Like 1

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Member
Exciting news that AI Hydra lights will soon be Mobius platform (similar to the rest of Ecotech). I got roped in to help with beta testing. Very nice interface and includes templates & additional features compared to the native AI app.
Will share more at a later time. Here is a screen shot :
946393993_20211216_092934000_iOS(Medium).png.e598d6338e1470d9fbf0ca825ecba16c.png
 
 
 
 


Hi bro, do you know how will this affect current AI app users? Means all will need to swap to mobius? I am so used to current AI app, simple and neat.


Sent from Singapore Reef Club mobile app
Link to comment
Share on other sites

  • SRC Supporter
1 hour ago, Otaku Reefer said:

 


Hi bro, do you know how will this affect current AI app users? Means all will need to swap to mobius? I am so used to current AI app, simple and neat. emoji28.png


Sent from Singapore Reef Club mobile app

 

I think the native AI app will still be around.

But have the option to move to Mobius - its a better platform. Even simpler & neater.

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Supporter
On 12/17/2021 at 9:39 PM, Ws_zaraki said:

Just wanna ask, do u find copepods in ur ATS?

Sent from Singapore Reef Club mobile app
 

Yes. Can see plenty of amphipods & copepods  whenever the hair algae is harvested.

 

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Supporter

Some pics taken today 

 

Love the daytime polyp extension.

1293784482_PC220239(Large).jpg.1c215647041df43201cc0bdd4391e65d.jpg

 

585467262_PC220258(Large).jpg.651d3191b51e0e6f06cf3cae992dae5a.jpg

 

Growth of this pink birdsnest seems to have accelerated the past few weeks. 

1794171680_PC220315(Large).jpg.55eee8c9ef7170b4710124e20e95add1.jpg

 

1124830117_PC220302(Large).jpg.f3721c40ed7fb9a97e87b704976e0635.jpg

 

 

About 2 months ago, I switched over to Coral Essentials line of additives after reading very good reviews about it. Its an Australian product & hence may not be so commonly mentioned in USA forums. Bought a set from Coral Fanatics. Note these are self purchased & wanted to use it for some time before sharing this update.

 

I've been advocate of having optimal levels of trace elements. From personal experience, when trace elements are out of spec (verified through ICP tests), corals tend to be less forgiving and tend to have problems (less PE, SPS tend to STN from the bottom, less vibrant colors, higher occurence of brown jelly). I suppose biological processes are inhibited (eg. poor nutrient transport to other parts of the colony that are not exposed to sufficient light).

 

378082552_P1010211(Large).JPG.6bffcbf466236bcc0ef77e35496c95b0.JPG

 

One good thing is that all the ingredients are declared in the product page. Full disclosure provided in the msds document. 

791101177_P1010217(Large).JPG.24b2ebd683eb4f862e0b55529bab1e88.JPG

CoralPower Trace A - Strontium & Barium. 

CoralPower Trace B - Iron, Zinc, Copper, Manganese, Chromium, Cobalt and Nickel

CoralPower Trace C - Potassium Iodide and Sodium Fluoride

CoralPower Potassium, Bromide & Boron - To enhance coloration + exoskeleton growth & cellular processes

 

2100494_P1010214(Large).JPG.ab1fdf086a83b48e334e45d943d5c3f8.JPG

CoralPower Amino - A blend of amino acids. For enzyme production, build protein for tissue growth & skeleton formation

CoralPower Gro - A blend of vitamins + L-Lysine (an amino acid). Liquid food source for growth & coloration. Improves polyp extension -> leads to more effective feeding

 

2113553565_P1010213(Large).JPG.82fd659d4c3c0f18ea398b4bc0a3b988.JPG

And finally the famous Black Label. From reviews, it to improve coloration, vibrancy and improve feeding response. On my end,  LPS are observed to be more puffy. Better polyp extension. Similarly, ingredients are fully declared in the MSDS. These are not cheap but decided to give it a try. 

Chroma+ : organic coenzymes to aid catabolism of sugars & amono acids

Vibrance + : aid rapid cell division & growth. 

Energy+ : For improved feeding & aid uptake of calcium, amino acids & vitamins -> improves growth

 

Dose is 1 drop per 100L  for Black Label, Amino, Gro, Potassium, Bromide & Boron.

And 2 drops per 100L for the Trace A, B, C.  

 

Everything looks good to date. An ICP test was done in September to get a baseline. The plan is to send for another round of ICP soon - to validate the dosing regime. 

 

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Supporter

More pics :

 

Branching golden hammer has a more yellowish tint now. 

1351519691_PC220291(Large).jpg.25b1348d2bb7d60d18675d4bb0668b55.jpg

 

Overgrown zoanthid on a frag rack.

393945916_PC220229(Large).jpg.e44c219ecfbe7cc3bde39e90193cf258.jpg

 

Space Invader Pectinia. Goal is for it to reach open palm size.

1911964141_PC220286(Large).jpg.7a96735ffc764ffee12271ffef3a1896.jpg

 

 

 

 

 

  • Like 1

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Supporter

A quick review on the Clarisea Gen 3 Fleece Filter.

Looking back, my old Clarisea Gen 2 (SK5000) has been running since April 2018. A longer fleece roll was introduced around June 2019. Increased from 25 meter to 40 meter (Same spec @ 20 microns. And for the same price). 

 

The Clarisea has been a game changer on my tank husbandry the past 3.5 years. Previously, I had to change the sump filter wool every 3 days to mitigate rising nitrate levels. With the Clarisea, the filter fleece is replaced just once every 2 months or so.  A common question I’ve been asked is whether the Clarisea is worth getting. I will probably never ever run a tank without the convenience of it.

 

I got hold of the Clarisea Gen 3 recently to replace my 3.5yr old Gen 2.

Its similar to the Gen 2 but with some nice improvements from assembly & usability point of view. I understand that there is no change to the fleece, motor & controller. Did some sump work today & its a good time to take some pics & provide actual usage update. As a quick recap during unboxing, the main panels came assembled out of the box. Just need to fasten a few more pieces after installing the filter fleece.

1472868394_20211226_085158944_iOS(Large).jpg.e39fff4998b59805e219c649629a1221.jpg

 

Gen 3 has a stiff roller to guide the fleece.

606429081_Gen3Clariseastiff.JPG.6506988806edc4953b6e907cc00f268d.JPG

 

This will prevent the fleece from bunching up like this seen in early Gen2 batches. The root cause is the white plate bends under the force of the taut fleece. And the curved shape of the plate causes the fleece to bunch up. I recall seeing current Gen2.5 version with this stiffener roller implemented already.

2057083361_Clariseabunchup.jpg.4fd3b2bce7ee3032c806970580a73145.jpg

 

Underside view : 

395065007_20211226_085048065_iOS(Large).jpg.10a767d1a8ab1ec0eed1d92bdcc96daa.jpg

 

I typically allow about 30% of the water to pass through. The bypass adjustment is now more accessible and located under the inlet pipe.

751456528_20211226_085058573_iOSa(Large).jpg.d100344196a5e919595198ce30b28cc5.jpg

 

I leave mine slightly open like this 1634246793_P1010397a(Large).JPG.71cdaadea15ebfeca66ece99f565dec7.JPG

 

Though some people may want to close it entirely for max filtration efficiency.

88334121_P1010393a(Large).JPG.012b707b214425cda2a604b31c6ae606.JPG

 

 Fleece removal tool. This is a convenient accessory to have. No more manual unwinding or cutting the dirty fleece with a blade. Just place the tool under the fleece & push down.

1507897103_20211226_090757694_iOSa(Large).jpg.bf17f42b5f2b6a3fe1b71a896591183d.jpg

 

Then push down (with 2 hands)

1290220614_20211226_090855750_iOSa(Large).jpg.ac9e66e808dcc028bd7f7208e1e28fbe.jpg

 

The clear acrylic panels are removable without any tools. It simplified the initial assembly process & makes it easier to take things apart when its time to give the unit a thorough wash.

1685482369_20211226_084750963_iOS(Large).jpg.39122fb8d07889f49a5a0934b89dd167.jpg

 

Looking at the picture, I just realised that I had assembled the used filter fleece incorrectly. You can see one end lifted off the acrylic. This happens when the motor wire is orientated to the bottom.

1858690102_P1010377b(Large).jpg.01fd974b32abd24eadf68b0fb2f639ef.jpg

 

The correct orientation should be this. 
I previously had a bad experience of the motor wire cut by the sharp acrylic edge. Got it serviced at Reef Depot (btw, good after service & warranty support). You can see from the picture below that Gen3 has a feature to prevent the the motor wire from being damaged by the acrylic edge. 
 

485676468_20211226_092517697_iOSa(Large).jpg.a8cfed79756676089c0e7a3fabc5196c.jpg

 

The fresh roll of fleece is supported by this simple acrylic holder. This design positions the fleece perfectly perpendicular and has less friction compared to Gen 2 holder (where the cardboard core is held by 2 sponge inserts). Less friction probably means the motor won’t need to work so hard.

339064246_20211226_084535159_iOS(Large).jpg.00b94729932501372e3e05bb24a33019.jpg

 

The fleece extension kit is now sold as a separate accessory. This is for folks with limited space & need to move the fresh fleece upwards. This is a pic from my old setup.

image.png.af2d228733624210896b43ea6342d6bc.png

 

Nice to see design principles deployed at the float switch to eliminate use of fasteners.

1261892853_P1010385a(Large).JPG.e94559f45b2ebbdcf8290ae95dc71843.JPG

 

The float switch shaft needs to be cleaned occasionally. Simply slide it off without the need to mess around with screws & nuts in that tight space.

1401552027_20211226_084143608_iOS(Large).jpg.1904331e3488525c48fca3438c8bc330.jpg

 

Tops down view showing the clean side & dirty side.

1151334167_Dirtyfleece.jpg.5314f13d7a25db1c39c0784f7744b719.jpg

 

To sum it all up: The Clarisea eliminates the mundane task of changing filter wool every few days. The latest Gen 3 performs similar to the previous Gen2.5 but has nice design & usability improvements.

 

 

 

 

  • Like 2

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Supporter

Time to move some colonies to make space for the growing clam.

PC220318.jpg.8764f2eb600bf70411c94649a1d4928a.jpg

 

Early morning torchlight pics. 

A fellow reefer's pectinia.

1083140390_20211103_215233786_iOS(Large).jpg.45b023b818ccf8bdb11130b569475b60.jpg

 

Percelain crab

534030461_20211026_223746156_iOS(Large).jpg.e76efdcf497e7fdc965111122ae746bc.jpg

 

 

 

  • Like 1
  • Haha 1

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Supporter

Water change today before the start of the new work year. 

DD H2Ocean has a new packaging. Classic Formula -> same as the previous Pro forumula.

 

407908630_P1010409(Large).jpg.757530e922a2b6d976243e6633709dbd.jpg

Some pics taken tonight taken with DD lens & iphone.

Hammer garden.

1334243606_20220103_133645696_iOS(Large).jpg.7c9f90b049529f7866d1a8267395b056.jpg

 

Sand bed is too messy.

1869695471_20220103_133825463_iOS(Large).jpg.8263c8acb656380f2c6b2d591764bf7f.jpg

 

This lobo is placed in super low light in the back corner of the tank behind the rocks.

16702403_20220103_133840049_iOS(Large).jpg.36f651b7c7ccb2d2e0f95762322eeaf8.jpg

 

Pic from Sept 2020. Traded with fellow reefer from Punggol.

image.png.d2bf0e1e91b018a1841049309c1e351a.png

 

The right frag was from a fellow reefer. 

866114762_20220103_133705667_iOS(Large).jpg.02baca2aa670583f7e8478b69f5a5e66.jpg

 

 

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • 2 weeks later...
  • SRC Supporter

Got inspired to do some retrofit for a 'smart home' after seeing Alston's setup. With his insights on equipment & some consultation (Thanks!!), I finally got it set up in December. With the zigbee hub in place, I did a little hack on the Sonoff door sensor to make it a wireless leak sensor.
441957892_P1010001(Large).JPG.71b9f0ab1aa70b5cd60a50807d8b21ea.JPG
 
Added a rain sensor PCB commonly used in arduino/raspberry pi projects
417713305_P1010003(Large).JPG.e8c423cc96e8cad52bf8a77f16b8a3a8.JPG
 
All cased up.20220116_085238562_iOS.jpg.1d3eeef828aefd9584ef7ea33f0dac77.jpg
 
The nice thing is that its wireless. 
Costs about $10 (excluding the zigbee hub)
1531069625_20220116_142833078_iOS1(Large).jpg.55ec7caad5cd62a9d013762012ef7101.jpg
 
 
Finally see the serpent star. My last purchase from Coral Farm on 23rd October. (i.e put in tank on 23rd Oct 21. Next seen 15th Jan 22). Good to know its alive.
759455394_20220115_004904883_iOS(Large).jpg.6ca0a96bf16abe9f3a06f8101b7d4d32.jpg
 
Some of the equipment on the left side of the tank.
I moved the ATO to the table recently. Quite ugly & plan to relocate it again.
Its very conveneint to have a tabletop space near the tank. Mine is a DIY 2020 aluminum profile stand with wooden panels straddling over the compressor. Its bolted to the tank cabinet for stability. 
Aside from the Alkatronic, Mastertronic and CO2 scrubber, there are 2x backup batteries for the wavemakers located under the table. 
 
1621428372_20220116_053459730_iOS(Large).jpg.a17c338dd56aa5de57f2733575e61c7b.jpg

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Supporter

Some fish pics taken today.

 

Springeri Damsel377487248_P1010060a(Large).jpg.4f8b76ea7e9be8fada8bcc81e0261464.jpg

 

469172212_20220123_055255048_iOS(Large).jpg.9eec0927e4829ff039e053f73cea0ba1.jpg

 

993012309_20220123_055327009_iOSa(Large).jpg.1ff2af859d702bbe9eaba348c788a8d9.jpg

 

The 3 clownfish have made the torches its home after all the bubble tip anemone were removed a couple of years back721300083_P1010077(Large).jpg.23d490529a56bab6b215b1c02376cb3e.jpg

 

One of my fav fish. But they are very fragile.334606773_P1010080(Large).jpg.73970dee086c37ec3d8321794593d28b.jpg

 

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Supporter

Some damage to the cynarina found this morning. Must have been stung by the sweepers from the chalice. Neighbours for the past year. I'd expect it to recover.

544587822_P1230025(Large).jpg.fcb522c45d640d7f807d0825ef45a4e1.jpg

 

Some daylight pics. No yellow filter.

Pink birdsnest.531187456_P1230016(Large).jpg.9f6a36a6b8b6788dd4102a55149fe502.jpg

 

Royal Blue Milli1521374848_P1230019(Large).jpg.e5cb8d16dd9e00d8f08a6423e5ac64dc.jpg

 

I think they call this Ultra Walt Disney tenuis.

1619261593_P1230013(Large).jpg.4d6853e6a392b9a4b906fb85b33b6d80.jpg

 

Overgrown bali slimer colony616529874_P1230049(Large).jpg.1570d763ea8991114c2cdd43a5d88ac3.jpg

 

 

Its been a month since using the Torq2 body. I must say that Nyos got it right with the 2nd iteration of the Torq.

The lids are very secure now. Coupled with the ease of removal for cleaning. And ease of rinsing media just by pouring fresh water down. I'm going to retire my old/regular media reactor and stick with the Torq2.

2083046805_20220119_141429065_iOS(Large).jpg.0440746fc50e99cd919571d0f219cc5b.jpg

 

 

 

534848352_20220119_141753742_iOS(Large).jpg.45071872d1272d7d23bfcf234a7b40d3.jpg

 

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • 2 weeks later...
  • SRC Supporter

Received several queries about the Clarisea Gen 3 and whether its a worthwhile equipment. 

Its been 1 month since the last new roll of fleece change. Below is the current state. I'd expect the roll to last approximately 2.5 months. This reason alone is enough to justify installing it - no need to mess around with dirty wool every few days. The additional rollers on the Gen3 seems to reduce the strain on the motors - so far its pulling effortlessly & no bunching observed.

1786845833_P1010004(Large).jpg.59186c25a664ddc1b3e2f91e04470198.jpg

 

Ideally the Clarisea be located towards the front of the sump with easy access to the dirty fleece roll.

973560863_P1010038(Large).jpg.f4734e6ed0d7641128376bcb23456a18.jpg

 

Someone also asked how the circuit breaker in my tank cabinet. Its good to have but not critical.

I have 6 power exension chords. Each is linked to a circuit breaker. In this way, if one item trips, there is a chance that it won't trip the rest of the breakers/equipment. For example, there are 2 return pumps in the tank. They are connected to different extension chords/breaker.

1696813936_P1010033(Large).jpg.c47fa70c04aa305d6cc18aef9c37ec2e.jpg

 

However, a backup battery for the wavemeker is considered essential. Very critical to keep the wavemaker going in the display tank if it trips even if its for a couple of hours. In the meantime, the Apex heartbeat function would notify if power in the house is out. It coule be 1 - 2 hours before you reach home. With the wavemaker still running, there is peace of mind there won't be serious issues during that time.

689654396_P1010034(Large).jpg.3cbe80e3712e711a5051f55478a0118a.jpg

The Coralbox battery is quite OK. The Ecotech one works best with the Vortech wavemakers & have a larger capcity as well.

 

 

 

 

  • Like 1

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Supporter

Phosphate levels dropped from around 0.2ppm on 23rd January to 0.02ppm on 1st February. The fluidization on the Torq reactor is fantastically good. I was not able to get this level of phosphate reduction with a regular reactor.

2043656692_P1010041(Large).jpg.daf20a224e4ec150153a24e66d42a39e.jpg602620146_20220119_141753742_iOS(Large).jpg.87d286065318daa165c562b532b4f72c.jpg

Parameters measured yesterday :

Salinity : 35ppm  / 1.0264SG

Ca : 380ppm -> Manually dose to 400ppm

Mg : 1400ppm

KH : 8.2

Potassium : 380ppm -> To manually dose to 400ppm

Phosphate : 0.02ppm

Nitrate : 5 ppm

 

Some pics from this weekend :

Closeup of the Bugatti Chalice

215942337_P2010062(Large).jpg.1937ecf25110d603bd076a589dba93dd.jpg

 

Sticking  a frag of blue dragon to the rock

1994235349_P1010011(Large).jpg.517da1c48cd6fd06fd85961f544de4a1.jpg

 

Clownfish fav hangout1018833226_P1010015(Large).jpg.c06e9a90aac24c6344a3c1c8a60e93d6.jpg

 

 

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Member
Received several queries about the Clarisea Gen 3 and whether its a worthwhile equipment. 
Its been 1 month since the last new roll of fleece change. Below is the current state. I'd expect the roll to last approximately 2.5 months. This reason alone is enough to justify installing it - no need to mess around with dirty wool every few days. The additional rollers on the Gen3 seems to reduce the strain on the motors - so far its pulling effortlessly & no bunching observed.
1786845833_P1010004(Large).jpg.59186c25a664ddc1b3e2f91e04470198.jpg
 
Ideally the Clarisea be located towards the front of the sump with easy access to the dirty fleece roll.
973560863_P1010038(Large).jpg.f4734e6ed0d7641128376bcb23456a18.jpg
 
Someone also asked how the circuit breaker in my tank cabinet. Its good to have but not critical.
I have 6 power exension chords. Each is linked to a circuit breaker. In this way, if one item trips, there is a chance that it won't trip the rest of the breakers/equipment. For example, there are 2 return pumps in the tank. They are connected to different extension chords/breaker.
1696813936_P1010033(Large).jpg.c47fa70c04aa305d6cc18aef9c37ec2e.jpg
 
However, a backup battery for the wavemeker is considered essential. Very critical to keep the wavemaker going in the display tank if it trips even if its for a couple of hours. In the meantime, the Apex heartbeat function would notify if power in the house is out. It coule be 1 - 2 hours before you reach home. With the wavemaker still running, there is peace of mind there won't be serious issues during that time.
689654396_P1010034(Large).jpg.3cbe80e3712e711a5051f55478a0118a.jpg
The Coralbox battery is quite OK. The Ecotech one works best with the Vortech wavemakers & have a larger capcity as well.
 
 
 
 

The backup battery may need to do some testing / checking if the battery is still holding the charge on a yearly basic too.. else when disaster happens and battery is faulty, there goes everything..


Sent from my iPhone using Tapatalk
Link to comment
Share on other sites

  • SRC Supporter
6 minutes ago, Sherilyn91 said:


The backup battery may need to do some testing / checking if the battery is still holding the charge on a yearly basic too.. else when disaster happens and battery is faulty, there goes everything..


Sent from my iPhone using Tapatalk

Fully agree. Actually I test for connectivity & power level every month or so by switching off the main plug for a couple of minutes.

Have 2 batteries hooked up. And replace them every 3 years or so. (Ecotech mentioned the battery lasting 3-5yrs)

Facebook : https://www.facebook.com/mysliceofnature/

 

 

 

 

 

Link to comment
Share on other sites

  • SRC Member
Fully agree. Actually I test for connectivity & power level every month or so by switching off the main plug for a couple of minutes.
Have 2 batteries hooked up. And replace them every 3 years or so. (Ecotech mentioned the battery lasting 3-5yrs)

Yes, In Singapore when the humidity and temp level is higher than oversea, battery fails way earlier than the recommended specification. Regular testing is good to ensure that all is good in case of a failure..


Sent from my iPhone using Tapatalk
Link to comment
Share on other sites

  • SRC Member

 
Other pics :
'Harvesting' pods & rotifers to feed the tank after lights off. Add together with about 1 cup of assorted phyto culture.
5ad76b623f635_P1013272(Large).thumb.jpg.2686c7d80df766d0baf2c7e8db32d6c2.jpg
 



Sorry to dig up an old thread, just researching on how to harvest pods and came across ur thread… can I find out how u do it? It seemed to have a gd yield from the pic

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.




  • Join us on the largest Reefing community in Asia!

    Sign up and share your reefing journey with us, make friends and get helps from the community .

     

  • Topics

  • Latest Update

    1. 2

      WTS 6" Foxface

    2. 1

      Storeroom Clearance

    3. 0

      加拿大保录取_SFU毕业证成绩单——Q微信751558146西蒙菲莎大学学位证_成绩单_办理SFU文凭学历认证Simon Fraser University

    4. 0

      美国学位证_Brandeis毕业证成绩单+Q微信751558146布兰迪斯大学学位证_成绩单_办理Brandeis文凭学历认证Brandeis University

×
×
  • Create New...