Return pump for chiller and display tank set up

[Yono_Pranata]

Hi Bros,

While awaiting for my new acquisition of tank. I'm thinking on how to set up my return pump display tank and chiller.

I'm planning to use 1 return pump to display tank and also feed my chiller pump.

Based on my research, there are 2 set up here:

1. Return pump - Chiller - Display Tank

2. Return pump - T Joint - Chiller and Display Tank

Which one is better?

Can you guys give me some advise? and for 322 size of tank, will Jebao DC10000 enough to feed my chiller and return pump to display tank?

Thanks in advance Bros!

[Guest]

Hi Bros,

While awaiting for my new acquisition of tank. I'm thinking on how to set up my return pump display tank and chiller.

I'm planning to use 1 return pump to display tank and also feed my chiller pump.

Based on my research, there are 2 set up here:

1. Return pump - Chiller - Display Tank

2. Return pump - T Joint - Chiller and Display Tank

Which one is better?

Can you guys give me some advise? and for 322 size of tank, will Jebao DC10000 enough to feed my chiller and return pump to display tank?

Thanks in advance Bros!

Hi bro i think if you state your chiller horse power or brand will help them answer you better.

Anyway flow rate for chiller the slower the more efficient.

Slower flow rate will have more contact time with the cooling coil

[Yono_Pranata]

Hi bro i think if you state your chiller horse power or brand will help them answer you better.

Anyway flow rate for chiller the slower the more efficient.

Slower flow rate will have more contact time with the cooling coil

Hi bro.. I'm still deciding whether should I take HS60A 1/4hp or HS90A with 1/2hp..

[Guest]

Hi bro.. I'm still deciding whether should I take HS60A 1/4hp or HS90A with 1/2hp..

Bro for me I'll say go with 1/4Hp.

Pros.

Size, heat that give out, cheaper and lesser noise.

Cons.

Take longer time to cool your temperature .

Your tank is 324 liters exclude sump

Description

HAILEA HS-66A Chiller

Power : 1/4 HP

Capacity : 300-500L

Flow Rate : 1000-2500L/H

Size : 435x295x470mm

I'll recommend this .

Is 66A not 60

This is a signature : hi

[Yono_Pranata]

Lols bro.. sorry typo error.. oopsss..

Ok. ThanKs bro for the advise..

How about the pump set up?

Cause I'm thinking to use lesser pump.. hahaha

[Solo77]

Option 1. 1/4 is more than enough. Pls know yr recommended flow rate for yr chiller and note that yr return pump flowrate will cut with distance and elbow joint.

[SubzeroLT]

The Jebao DC10000 is a good choice. You can adjust to run at lower power as necessary since its a DC pump. This is not possible for AC pumps.

And since its quite powerful, you can also T-off to run other reactors (eg. Rowaphos & Bio pellet)

For reference, I'm using a Jebao DC6000 running at 95% power 3x1.5x1.5. Hooked up to 1/4hp Hailea chiller.

[Solo77]

Do consider yr return pipe side to ensure it can take volume of water returning to sump.

[PoorPicasso]

might want to call seaview to ask for Hailea price.

[Yono_Pranata]

The Jebao DC10000 is a good choice. You can adjust to run at lower power as necessary since its a DC pump. This is not possible for AC pumps.

And since its quite powerful, you can also T-off to run other reactors (eg. Rowaphos & Bio pellet)

For reference, I'm using a Jebao DC6000 running at 95% power 3x1.5x1.5. Hooked up to 1/4hp Hailea chiller.

Bro - so the chilled water will go back to sump or straight to display?

[Yono_Pranata]

Do consider yr return pipe side to ensure it can take volume of water returning to sump.

Sorry bro.. did not quite get it..

Hahahah.. mind to explining more? I'm very sux in piping.. lols..

[SubzeroLT]

Bro - so the chilled water will go back to sump or straight to display?

I split the output of my return pump to the following rough approximate :

- 60% to chiller then directly back to display tank (1/2" diameter return pipe)

- 25% to biopellet reactor of which, part of it goes to rowaphos reactor

- 15% to refugium

[Guest]

Sorry bro.. did not quite get it..

Hahahah.. mind to explining more? I'm very sux in piping.. lols..

Your water example 10000L per hour.

Can your overflow pipe take that much water? Will your tank overflow with water if fish or something stuck in the pipe?

This is a signature : hi

[Yono_Pranata]

Your water example 10000L per hour.

Can your overflow pipe take that much water? Will your tank overflow with water if fish or something stuck in the pipe?

This is a signature : hi

Ooo.. understand.. so is jebao dc 10,000 or jebao dc 6,000 for 322?

I was thinking to just use dc 10,000 but control it to like 60% power..

[Yono_Pranata]

I split the output of my return pump to the following rough approximate :

- 60% to chiller then directly back to display tank (1/2" diameter return pipe)

- 25% to biopellet reactor of which, part of it goes to rowaphos reactor

- 15% to refugium

Wah.. like that also good ya.. save a lot of pump.. must get someone to help me install then.. lols..

[Yono_Pranata]

So all the bros, shall i set the chilled water to DT or back to sump tank?

Mind if someone enlighten me with the pros and cons..

Thanks!

[Guest]

Ooo.. understand.. so is jebao dc 10,000 or jebao dc 6,000 for 322?

I was thinking to just use dc 10,000 but control it to like 60% power..

I just explaining what he mean when he say water back to sump HAHAHA

This is a signature : hi

[Yono_Pranata]

I just explaining what he mean when he say water back to sump HAHAHA

This is a signature : hi

Oo.. sorry sorry bro! Blur already.. Hahahahha