Jump to content

Biopellets in TLF FR Clumping Together


JeffL
 Share

Recommended Posts

  • SRC Member

Anyone using TLF FR with Biopellets? The biopellets in the FR will clump and stick together every couple of months and it makes the biopellets inefficient. Have reduced the amount of biopellets down to only 3cm height but still clumping occurs. My FR is modified with the add-on mesh for biopellets...

Any idea why is this so?

Any other FR don't have this issue?

thanks in advance

2 Feet Tank: (Decom Feb 2015)
-Lightings : Pharos LED light 90W with wireless controller
-Chiller : Arctica 1/10HP with H2Ocean Flow Pump 2000

-Wavemaker : Vortech MP10ES
-Skimmer : Bubble Magus NAC 3.5

-Return Pump : Eheim Compact 3000
-Reactor – TLF150 (Mod) with NP Biopellet
-Reactor – TLF150 with Rowaphos


Link to comment
Share on other sites

This is mainly due to bacteria film generated from the bio pallet when it melts. This is also the reason why there is reactor cater specially for the bio pallet which tumble / move the bio pallets in various ways to prevent such clumping.

Take out the mesh on top of the FR and wash it , it will helps since most likely the mesh is cloak . Alternatively try consider running a bio pallet rector in future. HTH :)

Link to comment
Share on other sites

  • SRC Member

This is mainly due to bacteria film generated from the bio pallet when it melts. This is also the reason why there is reactor cater specially for the bio pallet which tumble / move the bio pallets in various ways to prevent such clumping.

Take out the mesh on top of the FR and wash it , it will helps since most likely the mesh is cloak . Alternatively try consider running a bio pallet rector in future. HTH :)

pardon my ignorance, what's a bio pellet reactor? I thought my TLF is already one.... hehe

I clean up just last week but didnt clean the sponge

2 Feet Tank: (Decom Feb 2015)
-Lightings : Pharos LED light 90W with wireless controller
-Chiller : Arctica 1/10HP with H2Ocean Flow Pump 2000

-Wavemaker : Vortech MP10ES
-Skimmer : Bubble Magus NAC 3.5

-Return Pump : Eheim Compact 3000
-Reactor – TLF150 (Mod) with NP Biopellet
-Reactor – TLF150 with Rowaphos


Link to comment
Share on other sites

pardon my ignorance, what's a bio pellet reactor? I thought my TLF is already one.... hehe

I clean up just last week but didnt clean the sponge

Hi bro,

I have the same problem too so I replaced it with Enductor Fluidized Reactor- FR30. IMHO, TLF initial design is mean for running po4 and carbon media so my advice is better use bio-reactor instead.

  • Like 1

post-1182-049500100201281969137_thumb.gi

Knowing is not enough; we must apply. Willing is not enough; we must do. - Goethe

Link to comment
Share on other sites

I take out the sponge and tubing and clean them when it happen.

After that all will run as usual

6.5 * 2 * 2 + 3.75 * 1.5 *1.5,(Decomn on 14/9/08)
4*2*2 + 2.5*1.25*1.25 (Decomn on 1/8/09)
5*2*2 (Fully LED light system, 140 3 watt SSC leds with 60 degree lens)(Decomm)
2.5*2*2(Fully LED Light System,96 3 watt SSC leds with 60 degree lens)(Decomm)

5*2.5*2(LED only)

Eheim return 1 * pump

1 HP Daikin compressor with cooling coil
2 Jebao OW40, 1 ecotech MP40,
1X6085 Tunze wm,

1 CURVE 7 Skimmer

  1 DIY 80 led control by Bluefish mini 

1 radion XR30W G2, 2 Radion XR15G3

Sump area lite by 5 ft T5 , 6 * SSC 3 watt red LED for refugium

1 Full spectrum E27 led light

1 CR control by bubble count

Start No Water Change since 1st Dec 2016

Add new 2.5x2x 1.5 ft 

 nLekOfpYts.jpg
[/quote]


 

Link to comment
Share on other sites

  • SRC Member

Hi bro,

I have the same problem too so I replaced it with Enductor Fluidized Reactor- FR30. IMHO, TLF initial design is mean for running po4 and carbon media so my advice is better use bio-reactor instead.

bro, I agree with you too. It is kinda modified to accommodate the use with biopellet.

Is Enductor a brand? Where can I find this... thanks!

2 Feet Tank: (Decom Feb 2015)
-Lightings : Pharos LED light 90W with wireless controller
-Chiller : Arctica 1/10HP with H2Ocean Flow Pump 2000

-Wavemaker : Vortech MP10ES
-Skimmer : Bubble Magus NAC 3.5

-Return Pump : Eheim Compact 3000
-Reactor – TLF150 (Mod) with NP Biopellet
-Reactor – TLF150 with Rowaphos


Link to comment
Share on other sites

pardon my ignorance, what's a bio pellet reactor? I thought my TLF is already one.... hehe

I clean up just last week but didnt clean the sponge

If you check out these video here, you will be able to see the different how the bio pallet tumble as compare to a normal reactor . This is to prevent it from clumping together.

Inductor Bio pallet reactor

Reef Octopus Bio churn Bio pallet reactor

Link to comment
Share on other sites

bro, I agree with you too. It is kinda modified to accommodate the use with biopellet.

Is Enductor a brand? Where can I find this... thanks!

You can get from reefsystem, ML or Madpetz.

post-1282-0-41590700-1374560774.png

post-1182-049500100201281969137_thumb.gi

Knowing is not enough; we must apply. Willing is not enough; we must do. - Goethe

Link to comment
Share on other sites

  • SRC Member

Hi everyone. Thanks for helping me out.

Does anyone know which FR is similar in size to the TLF? My sump is small. Don't really have much choices

2 Feet Tank: (Decom Feb 2015)
-Lightings : Pharos LED light 90W with wireless controller
-Chiller : Arctica 1/10HP with H2Ocean Flow Pump 2000

-Wavemaker : Vortech MP10ES
-Skimmer : Bubble Magus NAC 3.5

-Return Pump : Eheim Compact 3000
-Reactor – TLF150 (Mod) with NP Biopellet
-Reactor – TLF150 with Rowaphos


Link to comment
Share on other sites

Hi everyone. Thanks for helping me out.

Does anyone know which FR is similar in size to the TLF? My sump is small. Don't really have much choices

There is a junior size inductor bio pallet reactor available at Madpetz maybe you can go take a look.

Link to comment
Share on other sites

  • SRC Member

Actually i was previously using the TLF Phosban reactor for biopellets as well and if i remembered correctly, it is actually advised in the manual to turn up the flow weekly to prevent the clumping from happening... I used it for couple of months with no issues...

Also u might wanna check the flow size cos i remembered TLF suggested smthg like 300+ gallon per hour for use with bio pellet

:: just a noob ::

Link to comment
Share on other sites

Actually i was previously using the TLF Phosban reactor for biopellets as well and if i remembered correctly, it is actually advised in the manual to turn up the flow weekly to prevent the clumping from happening... I used it for couple of months with no issues...

Also u might wanna check the flow size cos i remembered TLF suggested smthg like 300+ gallon per hour for use with bio pellet

I have tried TLF150 running bio-pellet with 1500l/h pump before and it still clumping after 1-2 mths so now use it to run rowaphos instead.

post-1182-049500100201281969137_thumb.gi

Knowing is not enough; we must apply. Willing is not enough; we must do. - Goethe

Link to comment
Share on other sites

Hi everyone. Thanks for helping me out.

Does anyone know which FR is similar in size to the TLF? My sump is small. Don't really have much choices

How about The Innovative Marine MiniMax media reactors? Very nice and nano size but too bad no one bring in... :( !

post-1182-049500100201281969137_thumb.gi

Knowing is not enough; we must apply. Willing is not enough; we must do. - Goethe

Link to comment
Share on other sites

  • SRC Member

I have tried TLF150 running bio-pellet with 1500l/h pump before and it still clumping after 1-2 mths so now use it to run rowaphos instead.

Bro you are right! Out of curiosity, I channel about 2000L flow into the TLF yesterday to give it a try.

I reduced my biopellet into just 1cm height and gave it a good stir. It did tumble barely but within 1 hour, all biopellet clump together again :angry2: It seems like these biopellet that already being used for some time has a sticky layer on them making them clump easily.

2 Feet Tank: (Decom Feb 2015)
-Lightings : Pharos LED light 90W with wireless controller
-Chiller : Arctica 1/10HP with H2Ocean Flow Pump 2000

-Wavemaker : Vortech MP10ES
-Skimmer : Bubble Magus NAC 3.5

-Return Pump : Eheim Compact 3000
-Reactor – TLF150 (Mod) with NP Biopellet
-Reactor – TLF150 with Rowaphos


Link to comment
Share on other sites

  • SRC Member

Hey bro. Jeff.

I recall there is a video on YouTube shows how to modify tlf fr for bio Pellet. You May give it a try.

Thanks bro. If I am not wrong, that video shows an addition of a plastic mesh to the TLF FR. I added that already.... still the same.

Maybe there are other solutions out there. Let me do some more research

2 Feet Tank: (Decom Feb 2015)
-Lightings : Pharos LED light 90W with wireless controller
-Chiller : Arctica 1/10HP with H2Ocean Flow Pump 2000

-Wavemaker : Vortech MP10ES
-Skimmer : Bubble Magus NAC 3.5

-Return Pump : Eheim Compact 3000
-Reactor – TLF150 (Mod) with NP Biopellet
-Reactor – TLF150 with Rowaphos


Link to comment
Share on other sites

  • SRC Member

Guys, look what I found on YouTube!

Something new which I haven't seen before. Do you all think this will work?

http://youtu.be/SsNDrSfOXK8

2 Feet Tank: (Decom Feb 2015)
-Lightings : Pharos LED light 90W with wireless controller
-Chiller : Arctica 1/10HP with H2Ocean Flow Pump 2000

-Wavemaker : Vortech MP10ES
-Skimmer : Bubble Magus NAC 3.5

-Return Pump : Eheim Compact 3000
-Reactor – TLF150 (Mod) with NP Biopellet
-Reactor – TLF150 with Rowaphos


Link to comment
Share on other sites

  • SRC Member

Gosh, a wild idea just came up to my mind after watching this video! :idea:

I may still be able to use back my TLF after all. :superman:

2 Feet Tank: (Decom Feb 2015)
-Lightings : Pharos LED light 90W with wireless controller
-Chiller : Arctica 1/10HP with H2Ocean Flow Pump 2000

-Wavemaker : Vortech MP10ES
-Skimmer : Bubble Magus NAC 3.5

-Return Pump : Eheim Compact 3000
-Reactor – TLF150 (Mod) with NP Biopellet
-Reactor – TLF150 with Rowaphos


Link to comment
Share on other sites

Gosh, a wild idea just came up to my mind after watching this video! :idea:

I may still be able to use back my TLF after all. :superman:

Why not right since you still have your FR. Please share with this after your modification if it works. :evil:

Link to comment
Share on other sites

  • SRC Member

Why not right since you still have your FR. Please share with this after your modification if it works. :evil:

I guess everyone knows which direction I am heading.... :D

Btw, where can I get the eductor here in SG? Getting this from Fish Street takes ages...

2 Feet Tank: (Decom Feb 2015)
-Lightings : Pharos LED light 90W with wireless controller
-Chiller : Arctica 1/10HP with H2Ocean Flow Pump 2000

-Wavemaker : Vortech MP10ES
-Skimmer : Bubble Magus NAC 3.5

-Return Pump : Eheim Compact 3000
-Reactor – TLF150 (Mod) with NP Biopellet
-Reactor – TLF150 with Rowaphos


Link to comment
Share on other sites

  • SRC Member

Right. That s the video. IT works well to me.

Look forward to ur modified one. BRO.

thanks bro, this video really is useful! gonna find time and do the mod as per the video then gonna improve it with the eductor. :thumbsup:

2 Feet Tank: (Decom Feb 2015)
-Lightings : Pharos LED light 90W with wireless controller
-Chiller : Arctica 1/10HP with H2Ocean Flow Pump 2000

-Wavemaker : Vortech MP10ES
-Skimmer : Bubble Magus NAC 3.5

-Return Pump : Eheim Compact 3000
-Reactor – TLF150 (Mod) with NP Biopellet
-Reactor – TLF150 with Rowaphos


Link to comment
Share on other sites

Tried the method in the video! Din cut anything tho. The whole idea is that the inlet pipe must not touch e bottom of the canister. Therefore, I silicon e short pipe to the cover pipe. Flip the longer pipe upside down and run the pump and this is what I get..

http://youtu.be/6MmFx5V0Kt0

Follow Alex's Reefing Journey @ 

 

 


 

Link to comment
Share on other sites

  • SRC Member

Tried the method in the video! Din cut anything tho. The whole idea is that the inlet pipe must not touch e bottom of the canister. Therefore, I silicon e short pipe to the cover pipe. Flip the longer pipe upside down and run the pump and this is what I get..

http://youtu.be/6MmFx5V0Kt0

I came across something similar as I do more research.

Something I don't understand on silicon e short pipe to the cover pipe. Flip the longer pipe upside down

Does this mean, you have two red plastic mesh touching each other? You simply flip the long pipe over and attach it to the upper red mesh?

How long did you use this with no clumping problem? TIA!

2 Feet Tank: (Decom Feb 2015)
-Lightings : Pharos LED light 90W with wireless controller
-Chiller : Arctica 1/10HP with H2Ocean Flow Pump 2000

-Wavemaker : Vortech MP10ES
-Skimmer : Bubble Magus NAC 3.5

-Return Pump : Eheim Compact 3000
-Reactor – TLF150 (Mod) with NP Biopellet
-Reactor – TLF150 with Rowaphos


Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share



  • Join us on the largest Reefing community in Asia!

    Sign up and share your reefing journey with us, make friends and get helps from the community .

     

  • Topics

  • Latest Update

    1. 0

      加拿大保录取_SFU毕业证成绩单——Q微信751558146西蒙菲莎大学学位证_成绩单_办理SFU文凭学历认证Simon Fraser University

    2. 0

      美国学位证_Brandeis毕业证成绩单+Q微信751558146布兰迪斯大学学位证_成绩单_办理Brandeis文凭学历认证Brandeis University

    3. 0

      加拿大保录取_UBC毕业证成绩单——Q微信751558146英属哥伦比亚大学学位证_成绩单_办理UBC文凭学历认证University of British Columbia

    4. 0

      美国学位证_PSU毕业证成绩单+Q微信751558146宾州州立大学学位证_成绩单_办理PSU文凭学历认证Penn State University Park

×
×
  • Create New...