Jump to content

JEBAO WP-25


weekdaywarrior
 Share

Recommended Posts

Can PM me the price?

6.5 * 2 * 2 + 3.75 * 1.5 *1.5,(Decomn on 14/9/08)
4*2*2 + 2.5*1.25*1.25 (Decomn on 1/8/09)
5*2*2 (Fully LED light system, 140 3 watt SSC leds with 60 degree lens)(Decomm)
2.5*2*2(Fully LED Light System,96 3 watt SSC leds with 60 degree lens)(Decomm)

5*2.5*2(LED only)

Eheim return 1 * pump

1 HP Daikin compressor with cooling coil
2 Jebao OW40, 1 ecotech MP40,
1X6085 Tunze wm,

1 CURVE 7 Skimmer

  1 DIY 80 led control by Bluefish mini 

1 radion XR30W G2, 2 Radion XR15G3

Sump area lite by 5 ft T5 , 6 * SSC 3 watt red LED for refugium

1 Full spectrum E27 led light

1 CR control by bubble count

Start No Water Change since 1st Dec 2016

Add new 2.5x2x 1.5 ft 

 nLekOfpYts.jpg
[/quote]


 

Link to comment
Share on other sites

  • SRC Member

Brought a WP 25,found that the power supply is stated 12v 1500mah. Is this normal? I though DC controllable pump could run up till 24v? The pump I tried running on H and S1 assuming it has the most flow and electric consumption,was playing with my wattmeter and found it draw abit lesser then I expect. Or did I miss out sometin ?

Too many hobby......too little money!

Link to comment
Share on other sites

  • SRC Member

post-2925-0-79951700-1372831477_thumb.jp power supply of WP25

post-2925-0-80514100-1372831501_thumb.jp the pump magnet side says max 24v will comsume ard 23watt?post-2925-0-24554700-1372831486_thumb.jp the power supply seem like a 12v

post-2925-0-46200600-1372831800.jpg had a friend sent me his wp40 power supply.

  • Like 1

Too many hobby......too little money!

Link to comment
Share on other sites

Hi, have bought the wp25 that use the 1.5a and 24v adapter. The adapter blown and tripped my circuit breaker. Had to reset ELCB, and the wp25 no working. Went back to get a replacement set, and second time, similar thing happen. Only on the third replacement and try out at the lfs, then all things seem fine and been working good in my tank.

At first, I thought it my socket giving me problem, but I have used that same socket for laptop and other equipment like LED that drew more power without problem.

I no electrician, but I think the adapter need some serious QC to be done. Does the warranty cover the adapter as well?

Link to comment
Share on other sites

  • 2 weeks later...
  • SRC Member

Bought wp25 to replace my long faulty mp10. IMO too powerful for 1.5ft cube, but still mange to find a mode that is suitable for my tank. I am currently using W1 with S3 or S2 mode. My review: - once it is locked, you can still switch the modes and speed, it only lock down the adjustable duration setting. Don't quite make sense IMO, it should have locked everything except the feed mode. I have to keep the controller inside the cabinet just in case my sons go and press and play with it. - during feed mode, the pump stops for 10 mins. It will be nice if it just reduce the speed by 50% instead of stopping it. - very quite if compare with mp10 to get the same type of wave - powerful which limit the setting and the position of pump, doesnt really bother me much, once it is set I don't change it often - value for money, with that kind of price can't really complain much. - mp10 is good to have, but I m happy enough with just wp25

Link to comment
Share on other sites

if you find it very powerful, you can reduce the supply voltage to 12V (minimum). If you have adaptor for external harddisk, that will perfectly fit. Just confirm the polarity is the same. However, do it at your own risk although i heve been using it for some time now and using else mode.

Link to comment
Share on other sites

  • SRC Member

hi is WP25 suitable for 2 feet tank?

yea.am using one for my 2 feet too,the orignal 24v PS might be too strong unless u still to W1 mode and set to S3.

else get a 12v PS and it should be fine even in high mode:)

  • Like 1

Too many hobby......too little money!

Link to comment
Share on other sites

  • 2 months later...

Mine broke down after 3 days. not yet sure if power supply or controller has problem. The pump still pulsating in a low power. But the controller leds are off like no power. Anyone had the issue?

Sent from my GT-N5120 using Tapatalk

Link to comment
Share on other sites

  • SRC Member

hi is WP25 suitable for 2 feet tank?

more than enough..if find it too powerful can still set to 50% or 75%..

I running 2 in my 3 2 2.5 FOWLR..so far so good..I like the "ELSE" mode (random power)..

  • Like 1

@ 291213

Updated video: Kenyee FOWLR

http://m.youtube.com/my_videos

Link to comment
Share on other sites

  • SRC Member
Mine broke down after 3 days. not yet sure if power supply or controller has problem. The pump still pulsating in a low power. But the controller leds are off like no power. Anyone had the issue? Sent from my GT-N5120 using Tapatalk
Is there an orange light on the controller ? That is night mode .
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share




×
×
  • Create New...