Dinosaur

Haiz....... thats what I am curious to find out too why all died in there?

Nope, everything is fine except some raise in No2

err........... It use to be very fat one but recently months skinner and skinner then finally becomes too weak and thats why get stuck onto the powerhead (I guess). But it was all along eating as normal Hmmm........ could be some parasite in her stomach?? This photo was taken during Apr this year .....

Haiz............ problem is I'm away for a week leaving my wife to take care of my tank 24 snail and one yellow tang dead

Welcome to the graveyard club

Sorry it should be read as 'Yellow tang' Not Yellow tank

It has been with me for more than 2 years liaoz ....... it dies one day before I came back from oversea it gets herself stuck onto the powerhead R.I.P

This puzzle me too......... anyone knows why?

From last Saturday Till now ........ within a week

More than 20 of my 35 trochus snail died it climbs into the overflow and die in there Beware !!!!!!!! Beware!!!!!!!

how about to pay for the chartered flight *joking only* dun catch me

Okie........ anybody want to try?

. Press and hold "UP" and "DOWN" together until Display shows "Pon" (program unlocked). 2. "Pon" will only be displayed for a while and the water temperature will be shown again. 3. Press and hold "SET" until Display shows "b1". 4. Value for "b1" ("b2", "b3" etc) will appear after a while. 5. To change from "b1" to "b2" to "b3" etc, press "SET". 6. To change value in "b1", "b2", "b3" etc, press "UP" or "DOWN". 7. Press "SET" to confirm changed value. 8. After all changes have been made, wait for a while for the Display to show water temperature again. 9. If needed, press and hold "UP" and "DOWN" together until Display shows "Pof" (program locked). ------------------------------------------------------------------------------------------------ "b1" (SET Point, in degree, default = -) This is the same as pressing "SET" outside. It is used to set the chiller cut-off temperature. Example: If "b1" = 26, then the chiller will turn off when the water temperature is chilled to 26 degrees. "b2" (Ramp SET Point, in -, default = 0) No information. "b4" (Dead band, in -, default = 0) No information. "b5" (Upper Hysteresis, in degree, default = 1) Example: If "b5" = 1, then chiller will turn on when the water temperature raises 1 degree above the temperature set in "SET" (or "b1"). If "b16" set to 1, then can set "b5" in 0.1 resolution. Example "b5" = 0.7. "b6" (Lower Hysteresis, in degree, default = 5) Not used – For heater only. "b7" (Set Point Lower Limit, in degree, default = 18) Lowest temperature that the user can set in "SET" (or "b1"). "b8" (Set Point Upper Limit, in degree, default = 38) Highest temperature that the user can set in "SET" (or "b1"). "b9" (Anti-cycling Time, in second, default = 180) "b9" defines the minimum time the chiller will turn on again after the chiller turns off. Example: If "b9" = 300, then chiller will turn on at greater than or equal to 300 seconds after the chiller turns off. "b10" (Alarm Set Point, in degree, default = -50) The chiller will alarm when the water reaches this temperature. "b11" (Alarm Delay, in minute, default = 999) The chiller will alarm when the water reaches the temperature set in "b10" only after X minutes, where X = value in "b11". "b15" (Off-set, in degree, default = 0) Example: If the tank thermometer reads 25degrees but the chiller displays 28degrees, then set "b15" = -3 so that both the tank thermometer and chiller show 25degrees. "b16" (Resolution, in NA, default = 0) When "b16" = 0, the temperature resolution is 1degree. When "b16" = 1, the temperature resolution is 0.1degree. "b17" (Measuring Unit, in NA, default = 0) When "b17" = 0, the temperature is measured in degree C. When "b17" = 1, the temperature is measured in degree F. "b21" (-, in -, default = 3) No information. "b26" (-, in -, default = 0) No information.

It use to be $6 to $8 when I first started good money huh

Al least from the rear they will be able to tell if its a male or female right?

I am just speaking on behalf of all the guys here

dont try your luck

How about posting your photo

canot meh Singapore so small why bother to divide it ?

One piece of advice Don't ever think of getting someone else to stand in for you The picture taken can see your face very clearly It happens before where people try to get other to stand in and ended up both charged

1) Hamannbmw2003 - Jurong West 2) nleong - Boon Lay 3) Benz - Bukit Timah 4) Reefer Guy - Holland 5) chrislwp - Queenstown Strathmore Ave 6) Terryz_- Jurong West 7)Coral_Clams - Jurong West 8)Changfra - Jurong West 9)Glare - Hillview 10)BarraCuda - CCK 11)JL27AY - West Coast 12)jOO - Clementi 13) vtec3100 - CCK 14) Cleartank - Tiong Bahru!! 15)metals99 - CCK 16) Oceanblue - Bukit Batok & Bukit Panjang 17) moron - Hillview 18) vincegoh - Bukit Panjang 19) dankoo - CCK Loop 20) maxz- Tiong Bahru 21) Black - CCK Ave 4 22) Shieldk - Bukit Panjang 23) hoppinghippos - bukit timah 24) CoralReef - Teban Gardens 25) nqh71 - Jurong West St 81 26) Jason - Taman Jurong 27) Reef_LoVeR - Jurong West st61 28) lvcap - Clementi 29) Darren - Teban Gardens 30) Dinosaur - Bukit panjang

Indecent exposure Insulting the modesty of a women Whihc one har?

1. ah^siao (sengkang) 2. hghflyer (sengkang) 3. [P]owder Blue (Kallang) 4. Octopuffy (Bedok Reservoir Road) 5. Jas Soh (Lavender) 6. Hotsoup(Chai Chee) 7. Vanan (pasir ris) 8. Bwilly (Sembawang/Tampines) 9. Hon (Punggol) 10. HolySpirit (Tenah Merah) 11.drewy (pasir Ris) 12.onghm (sengkang) 13.jc85 (hougang/buangkok) 14.Kouz (Pasir Ris) 15.planetg(Hougang) 16.Tango_Liverock (Tampines) 17.Orgasbt(Pasir Ris) 18.Bob (Pasir Ris) 19. Dinosaur (Bukit Panjang)

Angel sold! Coral chip size 10 still available

SOLD! Thank You