erictanyh

- jackywongto - 110W - G2 - new_new - 160W x 2 - peacemaker - 110W - pandagold - 230w - G2 ( shd arrive end of this week ) - kikobananas - 110W - G1 - justin - 160w - binosage - 60W - m12345y - 110w x2 - G2 - ogykogy - 60w - oqs - 110w G2 (akan datang, coming shipment) - eictanyh - 110w- G2 ( Received 15/3/10)

At present, i only put 1 x ATI T5 Blueplus(39watt),1 x ATI T5 Aquablue Special(39watt), I have tried to add one more ATI T5 Aquablue Special but it is too bright for me...... Hope with 1 unit of G2-110w will just nice to my own prefrence...... my tank size is 3'(L) x 22"(H) x 17"(W) and if from my sand bed to the water lever, it only 16-17", so i hope with 1 unit of G2-110w will get me the good shimmer effect...... Anyway, Jacky, can i know Dr Evil is from which LFS in Singapore??? Thanks......

Ya... Thanks Jacky, just u2u him..... For Fish only tank in 36" tank, can i use only one G2 110w??? Thanks...

HI all sifus, I'm Eric from Penang, Malaysia. i can't get this Maxspect G2-110w from Malaysia...... Can anyone advise me where can i buy it online from Singapore dealer with the good price.... Thanks!!

Yes, many forumer faced this problem and many LPS even don't know about this...... you need to relocate the monitor not the probe far away from any electric devices. Remember don't buy the 9v AC adaptor too, it will cause the same problem too.....

Got the answer liow....... hope can help others...... " Other electrical devices causing interference with the display monitor. The most common culprit is high frequency electronic ballasts" Anyway, Thanks to hammy!!

No one use this device....???

Hi all sifu.... I just got the new American merine pH Pinpoint Monitor for my FOWLR marine tank, after i did the 7 and 4 calibration a few times and put into the tank, i noticed that the reading is quite fluctuated.... My problems are : 1) By using the AC adaptor, the reading fluctuarate between 7.51 and 7.78, these show lower ph value if i use the 9v batterry which show the reading 7.75 and 7.92...... why the reading is so different by using AC power and 9V battery....?? 2) Is the monitor reading normal if the 1st decimal point fluctuarate between 7.7 and 7.9...?? I beleive that it is normal if the reading of second decimal point is fluctuarating loh...... Please help and advice....... Thanks...!!

Hi, or you may sms me at +60124781838. Thanks....

Hi, i'm interested on your both items, what is your best price ah?? Can i know what is the size or the RM model?? But i'm from Penang, Malaysia. Thanks

Thanks!! I have found out the due to my drip rate too fast, so,the outlet got NO2 reading. One of the Malaysia Marine Club member ketam_batu posted this useful link : http://www.aqua-medic.com/products/docs/Ni...ductor_1000.pdf Really help!!

Hi, I have set up a DIY Sulphur Denitrator( One chamber Aquamedic sulphur, one chamber Aquamedic Calcium sand) 3 months ago. Yesterday I added one more set due to my current SD really can't bring down my NO3. I have reset my drip rate to 1-2drips/sec now and previously my drip rate is too slow(5-6sec/drip). My question now is i have 0.25ppm-0.5ppm reading of Nitrite(NO2) from my DIY SD outlet now!! Is that normal/ok?? Is this because of my SD not enough good bateria to handle it yet at this moment??Please advice..... Thanks...!!

Hi, I have set up a DIY Sulphur Denitrator( One chamber Aquamedic sulphur, one chamber Aquamedic Calcium sand) 3 months ago. Yesterday I added one more set due to my current SD really can't bring down my NO3. I have reset my drip rate to 1-2drips/sec now and previously my drip rate is too slow(5-6sec/drip). My question now is i have 0.25ppm-0.5ppm reading of Nitrite(NO2) from my DIY SD outlet now!! Is that normal/ok?? Is this because of my SD not enough good bateria to handle it yet at this moment??Please advice..... Thanks...!!